Honeywell Galaxy 3-520C - Page 99

Galaxy 3 Series Programming Manual
93
53 - Program Outputs (cont’d)
Key:
S = Activates when system is set ? = Activation dependant on system programming
P = Activates when system is Part Set X = Activates during Exit Time
U = Unset E = Activates during Entry Time
A = Activated in any condition L = Switches output off if linked to destination output
- = No effect T = Activates if zone resistance is less than value for tamper s/c
O= Activates when zone is omitted or greater than value for tamper o/c
Table 22D. Output Activations per Zone
Output Functions Set Late U/S
Early
Pre- Warn Autoset DR
Masked
Link A-O RF
Jam
RF
Super
Bell
Fail
Low
Volts
Lockout Vib
Test
Atm 1-4 Fault
Zone Function 46 47 48 49 50 51-65 66 67 68 69 70 71 72-75 76
01 Final –– ? – – ?––––––––
02 Exit –– ? –– ?––––––––
03 Intruder –– ? –– ?––––––––
04 24 Hours –– ? –– ?––––––––
05 Security –– ? –– ?––––––––
06 Dual –– ? – – ?––––––––
07 Entry –– ? –– ?––––––––
08 Push Set U? S? – – – ? – – – – – – – –
09 Keyswitch –– ? –– ?––––––––
10 Secure Final –– ? – – ?––––––––
11 Part Final –– ? –– ?––––––––
12 Part Entry –– ? –– ?––––––––
13 PA –– ? – – ?––––––––
14 PA Silent –– ? – – ?––––––––
15 PA Delay –– ? – – ?––––––––
16 PA Delay Silent –– ? – – ?––––––––
17 Link ?? ? ? ? ????–???–
18 Spare –– ? – – ?––––––––
19 Fire –– ? –– ?––––––––
20 Tamper –– ? –– ?––––––––
21 Bell Tamper –– ? –– ?––––––––
22 Beam Pair –– ? –– ?––––––––
23 Battery Low –– ? –– ?–––––––A
24 Line Fail –– ? – – ?–––––––A
25 AC Fail –– ? – – ?–––––––A
26 Log –– ? – – ?––––––––
27 Remote Access –– ? – – ?––––––––
28 Video –– ? – – ?––––––––
29 Video Exit –– ? – – ?––––––––
30 Intruder Delay –– ? – – ?––––––––
31 Log Delay –– ? –– ?––––––––
32 Set Log –– ? –– ?––––––––
33 Custom-A ?? ? ? ? ????–???–
34 Custom-B ?? ? ? ? ????–???–
35 Exitguard LL L L L LLLL–LLL–
36 Mask –– ? – – ?–––––––A
37 Urgent –– ? – – ?––––––––
38 PA Unset –– ? –– ?––––––––
39 Keyswitch Reset –– ? – – ?––––––––
40 Bell Fail –– – –– –––A––––A
41 Intr Low –– ? –– ?––––––––
42 Intr High –– ? – – ?––––––––
43 PSU Fault –– ? – – ?–––––––A
44–46 Not Used –– ? – – ?––––––––
47 Vibration –– ? – – ?–––––A––
48 ATM-1 –– ? – – ?––––––O–
49 ATM-2 –– ? –– ?––––––O–
50 ATM-3 –– ? –– ?––––––O–
51 ATM-4 –– ? – – ?––––––O–
52 Alarm Extent –– ? –– ?––––––––