Honeywell H910 Plus - User Manual

EN
H910 plus
User Instructions
APPLICATIONS: This filtering half mask is manufactured for COVID19 protection only. As requested by
World Health Organization recommendations, for this specific use, the nominal protection factor given by this
filtering half mask is the same than the FFP2 nominal protection factor defined in EN 149:2001+A1:2009.
This filtering half mask is not a filtering half mask for general use and shall not be used for purposes other
than protection against COVID19.
LIMITATIONS: Do not use this mask to enter or stay in an area where: • oxygen concentration is less than
17% (oxygen-deficient atmospheres) • contaminants and/or their concentrations are unknown or
immediately dangerous to life or health • aerosol concentration exceeds levels fixed by applicable health and
safety regulations or Protection Factor x WEL • gases and/or vapours are present • with open flames because
it is not flame resistant. Do not use this mask in explosive atmospheres.
HOW TO PUT ON A MASK: (1) The nose clip should face outwards
and upwards when holding the mask on each end of its ear bands;
(2) Wear the mask and place the chin inside the chamber. Pull the
ear bands over both ears; (3) Adjust until you feel comfortable and
the mask clings to the face: (4) Use the index finger and middle
finger of both hands to adjust the nose clip until it clings to the
nose bridge; (5) Conduct a tightness test, as shown in Figure 5:
• Cup the mask in both hands and keep the mask still. • Try to
inhale and hold your breath for several seconds; and you will feel
that the mask collapses inwards. • Try to exhale and hold your
breath for several seconds: and you will feel that the mask expands
outwards. • In case of air leakage, please repeat Steps 13 above
until the requirements of both 2 and 3 are satisfied. • A mask
cannot meet the requirements of protective-rating airtightness
until the test results of step 13 above live up to expectations.
The mask has maximum effectiveness when it is worn on direct contact with bare skin. It is unlikely that
the requirements for leakage will be achieved if facial hair passes under the face seal.
USE: (1) Take a new mask from its box. (2) Check visually that the mask is undamaged and stored protected
against contamination before each use. (3) Fit the mask and check leak-tightness before entering the
contaminated area. (4) Wear it for the whole duration of exposure to contaminants. (5) Discard it and replace
with a new one if: • it is removed while in a contaminated area • excessive clogging causes breathing difficulty
or discomfort • it becomes damaged. Do not alter the mask. Leave the contaminated area if dizziness,
irritation or other distress occurs.
The filtering half mask shall not be used for more than one shift.
STORAGE: Do not store in temperatures below 20°C or above +38°C or in an atmosphere with a
relative humidity above 80%.
DISPOSAL: Remove the mask with washed/ disinfected hands to avoid any contamination. If wearing
a protective gloves, take them off first. Only touch the ear loops Hold both of the ear loops and gently lift
and remove the mask. Discard the mask in a dedicated bin (touchless bin with lid and double bagging is
recommended for safety reasons). Wash or disinfect your hands.
APPROVALS: Product complies with the European Parliament and Council Regulation 2016/425/EU for
Personal Protective Equipment and subsequent amendments. The EU type-examination as per Module
B of PPE Regulation is carried out by the notified body number 1463: POLSKI REJESTR STATKÒW S.A. -
Aleja Generała Jòzefa Hallera 126 - 80416 GDAŃSK - POLAND.
The production process based on quality
assurance of the conformity to type set out in Module D of PPE Regulation is under surveillance of the
notified body number 0082: APAVE SUDEUROPE SAS - CS60193 - 13322 MARSEILLE Cedex 16 – FRANCE.
The EU declaration of conformity is available on the website https://doc.honeywellsafety.com/.
Honeywell Middle East Industrial Company LLC
 info-meta.hsp@honeywell.com
 +971 4 4505800
 www.honeywellsafety.com/MEI
PPE-R/02.075 version 1 (FFP2)
ME5590A-ME Rev.A 05/2020

Summary

Applications and Limitations

Applications

Specifies the mask is for COVID-19 protection only and its FFP2 equivalence.

Limitations

Details conditions under which the mask should not be used, like low oxygen or unknown contaminants.

How to Put On a Mask

Conducting a Tightness Test

Step-by-step guidance on performing the mask seal test by inhaling and exhaling.

Fit and Skin Contact

Notes on achieving maximum effectiveness by wearing on bare skin, avoiding facial hair interference.

Usage and Maintenance

Mask Usage

Instructions for checking, fitting, and wearing the mask during exposure to contaminants.

When to Discard and Replace

Specifies conditions requiring the mask's replacement, such as clogging or damage.

Usage Duration

Indicates the filtering half mask shall not be used for more than one shift.

Storage and Disposal

Storage Conditions

Guidelines for proper storage temperatures and humidity to maintain mask integrity.

Disposal Instructions

Instructions on how to safely remove and dispose of the mask to prevent contamination.

Approvals and Declarations

Product Approvals

Lists compliance with EU regulations for Personal Protective Equipment (PPE).

EU Declaration of Conformity

Information on where to find the EU declaration of conformity for the product.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The Honeywell H910 plus is a filtering half mask specifically manufactured for COVID-19 protection. It is designed to meet the nominal protection factor equivalent to FFP2 as defined in EN 149:2001+A1:2009, in accordance with World Health Organization recommendations for this specific use. It is crucial to note that this mask is not intended for general use and should only be utilized for protection against COVID-19.

Function Description:

The primary function of the H910 plus filtering half mask is to provide respiratory protection by filtering airborne particles, specifically those associated with the COVID-19 virus. When properly worn, it creates a seal around the user's face, preventing the inhalation of contaminated air. The mask achieves maximum effectiveness when worn in direct contact with bare skin, as facial hair passing under the face seal can compromise its leakage requirements.

Important Technical Specifications:

• Protection Level: Equivalent to FFP2 nominal protection factor as per EN 149:2001+A1:2009.
• Application: Exclusively for COVID-19 protection.
• Flame Resistance: Not flame resistant.
• Storage Temperature: -20°C to +38°C.
• Storage Humidity: Below 80% relative humidity.
• Regulatory Compliance: Complies with European Parliament and Council Regulation 2016/425/EU for Personal Protective Equipment (PPE) and subsequent amendments.
• Notified Bodies:
  • EU type-examination (Module B): POLSKI REJESTR STATKÓW S.A. (Number 1463), Aleja Generała Józefa Hallera 126 - 80-416 GDAŃSK - POLAND.
  • Production process surveillance (Module D): APAVE SUDEUROPE SAS (Number 0082), CS60193 - 13322 MARSEILLE Cedex 16 – FRANCE.
• CE Marking: CE0082.
• Document Reference: PPE-R/02.075 version 1 (FFP2).

Usage Features:

The H910 plus is designed for single-shift use and should not be used for more than one shift.

• Pre-Use Check: Before each use, users must visually inspect the mask to ensure it is undamaged and has been stored protected against contamination.
• Donning Procedure:
  1. Hold the mask by its ear bands with the nose clip facing outwards and upwards.
  2. Place the mask on the face, ensuring the chin is inside the chamber, and pull the ear bands over both ears.
  3. Adjust the mask for comfort until it clings to the face.
  4. Use the index and middle fingers of both hands to adjust the nose clip until it clings to the nose bridge.
  5. Tightness Test: Cup the mask in both hands, keep it still, and try to inhale and hold your breath for several seconds. The mask should collapse inwards. Then, try to exhale and hold your breath for several seconds; the mask should expand outwards. If air leakage is detected, repeat steps 1-3 until the mask fits properly.
• Duration of Use: The mask should be worn for the entire duration of exposure to contaminants.
• Disposal: The mask must be discarded and replaced with a new one if:
  • It is removed while in a contaminated area.
  • Excessive clogging causes breathing difficulty or discomfort.
  • It becomes damaged.
  • Users should leave the contaminated area if dizziness, irritation, or other distress occurs.
• Limitations: This mask should not be used in areas where:
  • Oxygen concentration is less than 17% (oxygen-deficient atmospheres).
  • Contaminants and/or their concentrations are unknown or immediately dangerous to life or health.
  • Aerosol concentration exceeds levels fixed by applicable health and safety regulations or Protection Factor x WEL.
  • Gases and/or vapours are present.
  • Open flames are present (as the mask is not flame resistant).
  • Explosive atmospheres exist.

Maintenance Features:

The H910 plus is designed for single-use and does not require traditional maintenance.

• Storage: Store the mask in its original packaging in a clean, dry environment within the specified temperature and humidity ranges (-20°C to +38°C, below 80% relative humidity) to maintain its integrity and effectiveness.
• Disposal Procedure:
  1. Remove the mask with washed/disinfected hands to avoid contamination. If wearing protective gloves, remove them first.
  2. Only touch the ear loops.
  3. Hold both ear loops, gently lift, and remove the mask.
  4. Discard the mask in a dedicated bin (touchless bin with lid and double bagging is recommended for safety reasons).
  5. Wash or disinfect your hands after disposal.
• Alterations: Do not alter the mask in any way. If the mask is damaged or altered, it must be discarded.

Honeywell H910 Plus Specifications