Honeywell HRG4 - Troubleshooting the IR Remote Control

To Next Page

To Previous Page

800-12005V1 - A - 08/2012

Solutions | 125

Troubleshooting the IR Remote Control

If this happens … Try this …

The Status indicator does not

turn green and there is still no

response from the remote.

Check the following:

• Ensure that the batteries are properly installed, and that the polarities of the

batteries are not reversed.

• Ensure that the batteries are fresh and are not out of charge.

• Ensure that the IR receiver is not obstructed.

• Ensure that no fluorescent lamp is used nearby.

Main Page

Contents1
- Canadian Compliance Statement5
- Cautions and Warnings5
- Regulatory Statements5
- Safety Standards5
- Safety Instructions6
- Warranty and Service7
- Table of Contents9
Figures13
Tables17
About this Document19
- Overview of Contents19
- Related Documents20
- Typographical Conventions20
1 Introduction23
- Overview23
- Operating the HRG DVR26
2 Getting Started35
- Starting and Shutting down the HRG DVR35
  - Starting the HRG DVR35
  - Shutting down the HRG DVR35
- Rebooting and Locking the HRG DVR36
- Using the Setup Wizard36
- Figure 2-1 Shutdown Menu36
- Figure 2-2 Setup Wizard37
- Figure 2-3 User Permission Window37
- Figure 2-4 Entering the HDD Management Window38
- Figure 2-5 HDD Management Window38
- Figure 2-6 Entering the Record Settings Window39
- Figure 2-7 Schedule Tab39
- Figure 2-8 Entering a New Recording Schedule40
- Figure 2-9 Copying a Schedule40
- Figure 2-10 Entering the Network Settings Window41
- Figure 2-11 Network Settings Window41
- Figure 2-12 Setting the Date and Time41
- Setting the Date and Time42
3 Live View43
- On-Screen Display in Live View43
  - Live View Icons43
- Operating Live View44
- Configuring the Live View Display46
4 Recording Settings49
- Configuring Recording Settings49
- Protecting Recorded Files53
5 Playback57
- Video Playback57
6 Backup63
- Backing up Recorded Files63
7 Alarm Settings69
- Configuring Alarms69
- Exception Settings80
8 Network Settings83
- Configuring Network Settings83
9 PTZ Control91
- Navigating the PTZ Menu91
- Figure 9-1 PTZ Menu91
- Configuring PTZ Settings92
- Figure 9-2 PTZ Settings Menu92
- Setting PTZ Presets, Patrols and Patterns93
10 Camera Management97
- OSD Settings97
- Figure 10-1 Camera Settings Menu97
- Image Settings98
- Figure 10-2 Advanced Camera Settings Menu98
- Figure 10-3 Image Settings98
- Privacy Mask Settings99
- Figure 10-4 Advanced Camera Settings Menu99
- Figure 10-5 Setting Mask Area99
11 Hard Drive Management101
- Managing Hard Drives101
12 HRG DVR Management107
- Configuring System Settings107
- Setting the RS-232 Port109
- Figure 12-3 RS-232 Settings Menu109
- Managing User Accounts110
- Managing the System114
  - Importing and Exporting the Configuration File114
  - Figure 12-9 Modify User Menu114
- Updating the System Firmware115
- Figure 12-10 Import/Export Configuration Menu115
- Figure 12-11 Firmware Update Menu116
- Figure 12-12 FTP Firmware Update116
- Restoring the Default Settings117
- Figure 12-13 Default Settings Menu117
- Viewing the System Information118
- Viewing the System Log118
- Figure 12-14 System Information118
- Figure 12-15 Log Search Menu119
- Figure 12-16 Log Search Results119
- Figure 12-17 Log Search Export Menu120
Appendix A Glossary121
Appendix B Solutions123
- Troubleshooting the HRG DVR123
- Troubleshooting the IR Remote Control125
Appendix C Specifications127
- Dimensions129
Index131

Honeywell HRG4 - Troubleshooting the IR Remote Control

Table of Contents

Other manuals for Honeywell HRG4

Related product manuals