Honeywell IntelliPath LTE-CFV

I
I
n
n
t
t
e
e
l
l
l
l
i
i
P
P
a
a
t
t
h
h
T
T
M
M
S
S
e
e
r
r
i
i
e
e
s
s
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
o
o
r
r
L
L
T
T
E
E
-
-
C
C
F
F
V
V
L
L
T
T
E
E
-
-
C
C
F
F
A
A
C
C
o
o
m
m
m
m
e
e
r
r
c
c
i
i
a
a
l
l
F
F
i
i
r
r
e
e
P
P
a
a
n
n
e
e
l
l
I
I
n
n
t
t
e
e
r
r
n
n
e
e
t
t
a
a
n
n
d
d
C
C
e
e
l
l
l
l
u
u
l
l
a
a
r
r
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
o
o
r
r
Installation and Setup Guide
800-24454 9/18 Rev A

Honeywell IntelliPath LTE-CFV Specifications

General

Push-to-Talk (PTT)	Yes
GPS	Yes
Cellular Connectivity	LTE
Primary Use	Mobile communication, safety, and security
Network Technology	LTE
Bluetooth	Bluetooth 4.2

Summary

Section 1: General Information

Compliance

Details requirements for UL864/NFPA compliance, including installation standards and power sources.

SECTION 2 Mounting and Wiring

Determine the Signal Quality and Select a Location

Guides on selecting a mounting location based on signal strength and RF exposure considerations.

Mount the Communicator

Instructions for mounting the communicator cabinet, including wiring, grounding, and securing the door.

Wire the Communicator

Details ECP wiring to compatible control panels, including UL requirements and wire gauge.

SECTION 3 Programming the Communicator

Programming the Control Panel to work with the LTE-CF

Details essential programming field settings for commercial control panels to interface with the LTE-CF.

Programming for UL864 Compliance

Details requirements for UL864 compliance, including supervision intervals and fault times.

Using the AlarmNet 360 Website

Guides on programming the communicator via the AlarmNet 360 website, requiring specific account information.

Using a 7720 P Programming Tool

Explains how to connect and use the 7720P Programming Tool, detailing key functions and prompts.

Programming

Details the ECP messaging and prompts for programming the communicator, including notes on remote access denial.

Comm Path Choice (2010 IP & Cell)

Explains the dual-purpose Comm Path Choice option and its impact on supervision and fault times.

Exiting Programming Mode

Guides on how to exit programming mode, including upload status and reset procedures.

Setting Factory Defaults

Explains how to reset programming options to factory defaults using the ESC key.

SECTION 4 Registration

Registering the Communicator

Explains the importance of registering the communicator to enable the AlarmNet account and reporting.

Registering through the AlarmNet 360 Website

Provides steps to register via the AlarmNet 360 website, listing required information.

Replacing an existing communicator

Guides on replacing an existing communicator using a PIN number and the 7720P tool.

SECTION 5 Programmer Keyboard Commands

Cell Status Displays

Details commands for viewing cellular status, including RAT, SigQual, REG, RSRP, and RSRQ.

Run Network Diagnostic Test

Explains how to run network diagnostics to test link integrity between communicator and AlarmNet.

System Status Display

Details commands for displaying system status, including ECP faults and network connectivity.

Registration

Explains the command to register a programmed communicator with AlarmNet.

Registration with PIN for Replacement Communicator

Guides on registering a replacement communicator using an existing PIN.

SECTION 6 Network Diagnostics

Running Network Diagnostics

Explains how to initiate network diagnostics using the 7720P tool and the requirements for it to run.

Wiring Diagram

Wiring Diagram