Honeywell IntelliPath Series User Manual

I
I
n
n
t
t
e
e
l
l
l
l
i
i
P
P
a
a
t
t
h
h
T
T
M
M
S
S
e
e
r
r
i
i
e
e
s
s
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
o
o
r
r
L
L
T
T
E
E
-
-
I
I
V
V
L
L
T
T
E
E
-
-
I
I
A
A
L
L
T
T
E
E
-
-
I
I
C
C
I
I
n
n
t
t
e
e
r
r
n
n
e
e
t
t
a
a
n
n
d
d
C
C
e
e
l
l
l
l
u
u
l
l
a
a
r
r
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
o
o
r
r
Installation and Setup Guide
800-24453 9/18 Rev A

Honeywell IntelliPath Series Specifications

General

Brand	Honeywell
Model	IntelliPath Series
Category	Cell Phone
Language	English

Summary

General Information

System Features

Encryption

Remote Services

Modes of Operation

Covers the different operational modes like ECP and Zone Trigger for various control panels.

Supervision Features

Details the types of supervision and fault detection provided by the communicator.

Specifications

Lists the technical specifications including mechanical, electrical, and environmental details.

Compatibility

Identifies compatible control panels and receivers for UL and ULC installations.

Compliance

Mounting and Wiring

Determine the Signal Strength and Select a Location

Guides on finding an optimal installation site based on signal strength.

Mounting the Communicator

Provides instructions for physically mounting the communicator unit.

Mounting Procedure, LTE-I (no rear tamper switch)

Step-by-step guide for mounting the LTE-I without a rear tamper switch.

Mounting Procedure, LTE-I (with rear tamper switch)

Step-by-step guide for mounting the LTE-I with a rear tamper switch installed.

Wiring the Communicator

Details the necessary wiring connections for the communicator.

Wiring for ECP

Explains how to wire the communicator for ECP mode with compatible control panels.

Wiring for Zone Trigger Mode

Describes wiring for Zone Trigger mode, including positive, negative, and EOLR triggers.

Wiring the Fault Relay

Instructions for wiring the fault relay for fail-safe mode.

Internet Connection

Covers connecting the communicator to the internet via Ethernet.

Power Connections and Options

Explains different methods for powering the communicator.

Powering the Communicator

Details standard, ULC, and shared transformer installation power methods.

Backup Battery Connection

Instructions for connecting the backup battery for power loss protection.

Programming the Communicator

General Information

Using the AlarmNet 360 Website

Using a 7720P Programming Tool

Using the Control Panel Programming Mode

Programming Conventions

ECP Mode Programming

Detailed steps for programming the communicator in ECP mode.

ECP Status Codes

Zone Trigger Mode

Explains programming for Zone Trigger mode, including zone inputs and options.

Registration

Registering the Communicator

Overview of the registration process and available methods.

LED Status Indicators

Registering through the AlarmNet 360 Website

Detailed steps for registering via the AlarmNet 360 website.

Register using the Tamper Switch

Describes how to initiate registration using the tamper switch.

Register using the Programming Tool

Replacing an existing communicator

Register by Phone

Programmer Keyboard Commands

Identification Displays

Network Diagnostics Display

Cellular Status Displays

Network Diagnostics

Running Network Diagnostics

Initiates network diagnostic tests to check link integrity with AlarmNet.

Possible Errors Running Network Diagnostics

Summary of Connections

Communicator TB1 Wiring

Table detailing TB1 wiring for ECP Mode and Zone Trigger Mode.