Honeywell ST 3000 - Page 22

34-ST-03-64
Page 22
STR14
A
STR12D & 13D 14G & 17G
TABLE II - SEALS (continued)
_ _ _ _ _ _ _ _ _ _ _ 0
●● ●
_ _ _ _ _ _ _ _ _ _ _ H
666
_ _ _ _ _ _ _ _ _ _ _ J
666
(Metal plug material _ _ _ _ _ _ _ _ _ _ _ M 666
will be the same as _ _ _ _ _ _ _ _ _ _ _ N 666
Cal. ring material if _ _ _ _ _ _ _ _ _ _ _ P
666
metal plug is chosen - _ _ _ _ _ _ _ _ _ _ _ Q
666
SS Plug for CS Lower)
_ _ _ _ _ _ _ _ _ _ _ R
666
_ _ _ _ _ _ _ _ _ _ _ S
666
Table II continued below
*
Standard facing 125-250 AARH RF (raised face) serrated surface finish.
**
Limited vacuum availability.
***
Minimum static pressure requirement. No vacuum allowed. See Specifications Figure 15.
****
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
a
Tantalum Upper insert has Tantalum wetted parts and 316 SS or CS non-wetted parts
Note:
Remote seal system pressure rating is body rating or seal rating, whichever is less.
STR12D & 13D STR14A
14G & 17G
TABLE II - SEALS (continued)
ANSI 150 22 _ _ _ BCA _ _ _ _ _ _
t4●
ANSI 300 22 _ _ _ BCC _ _ _ _ _ _
t4●
ANSI 150 22 _ _ _ BGA _ _ _ _ _ _
t4●
ANSI 300 22 _ _ _ BGC _ _ _ _ _ _
t4●
ANSI 150 22 _ _ _ BDA _ _ _ _ _ _ t4●
ANSI 300 22 _ _ _ BDC _ _ _ _ _ _ t4●
ANSI 150 22 _ _ _ BFA _ _ _ _ _ _ t4●
ANSI 300 22 _ _ _ BFC _ _ _ _ _ _
t4●
1/2" ANSI 150 23 _ _ _ CAA _ _ _ _ _ _
●● ●
ANSI 150 23 _ _ _ CCA _ _ _ _ _ _
●● ●
ANSI 300 23 _ _ _ CCC _ _ _ _ _ _
●● ●
ANSI 150 22 _ _ _ CGA _ _ _ _ _ _
●● ●
ANSI 300 22 _ _ _ CGC _ _ _ _ _ _ ●● ●
ANSI 150 22 _ _ _ CDA _ _ _ _ _ _ ●● ●
ANSI 300 22 _ _ _ CDC _ _ _ _ _ _ ●● ●
1/2" ANSI 150 22 _ _ _ DAA _ _ _ _ _ _
●● ●
ANSI 150 23 _ _ _ DCA _ _ _ _ _ _
●● ●
ANSI 300 23 _ _ _ DCC _ _ _ _ _ _
●● ●
ANSI 150 23 _ _ _ DGA _ _ _ _ _ _
●● ●
ANSI 300 23 _ _ _ DGC _ _ _ _ _ _
●● ●
ANSI 150 23 _ _ _ DDA _ _ _ _ _ _ ●● ●
ANSI 300 22 _ _ _ DDC _ _ _ _ _ _ ●● ●
ANSI 150 22 _ _ _ DFA _ _ _ _ _ _ ●● ●
ANSI 300 22 _ _ _ DFC _ _ _ _ _ _
●● ●
Table II continued next page
*
Standard facing 125-250 AARH RF (raised face) serrated finish.
**
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Note:
Remote seal system pressure rating is body rating or seal rating, whichever is less.
Two 1/2" with plastic plugs
Selection
Flange
Pressure
Rating *
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
2"
1-1/2"
3"
4.1"
2.9"
1-1/2"
1-1/2"
Flush Flanged
Seal
Flange
Size
Diaphragm
Diameter
Connections
and Plugs****
Flushing
2"
Selection
Construction - See Spec.
Figure 34-ST-03-64
Const. - See
Spec. Figure 34-
ST-03-64
Two 1/2" with metal plugs
1"
Flush Flanged
Seal with Lower
2.4"
3"
1"
2"
1"