What does 'No DAC Calibration' mean on Honeywell ST 700 Transmitter and how to solve it?
This status on your Honeywell Transmitter indicates that no DAC calibration has been performed on the device. Perform DAC calibration for precise analog output measurement.
What to do if a critical failure has been detected on the HART, DE, or FF Electronics Module of Honeywell ST 700 Transmitter?
If a critical failure is detected on the HART, DE, or FF Electronics Module, cycle power to the transmitter. If the problem continues, replace the Electronics Module.
What to do if a critical failure has been detected in the Meter body of Honeywell ST 700?
If a critical failure has been detected in the Meter body, cycle power to the Transmitter. If the problem continues to occur, replace the Meter body.
What to do if my Honeywell ST 700 displays 'Sensor Comm Timeout'?
If your Honeywell Transmitter shows a 'Sensor Comm Timeout' error, it means there's likely no response from the sensor. First, try replacing the Electronics module. If the issue continues, then replace the Meter Body.
What does 'No DAC Compensation' mean on Honeywell ST 700 Transmitter and how to solve it?
This status on your Honeywell Transmitter indicates that no temperature compensation data exists for analog output calculations, which may slightly compromise loop accuracy. Replace Electronics Module (PWA) to achieve the maximum current loop accuracy or return the device to factory for DAC compensation.
What to do if Honeywell ST 700 displays 'Fault. A critical failure has been detected in the Meter body'?
If your Honeywell Transmitter displays a fault indicating a critical failure in the Meter body, cycle power to the Transmitter. If the problem continues to occur, replace the Meter body.
What does 'RAM fault' mean on Honeywell Transmitter and how to solve it?
This status on your Honeywell Transmitter indicates that the RAM in the Sensor board is corrupt or the RAM database in the Sensor board is compromised. Reset the device. If the problem persists, replace the Meter Body.
What does 'NVM fault' mean on Honeywell Transmitter and how to solve it?
This status on your Honeywell Transmitter indicates that the NVM in the Sensor board is corrupt or the NVM in the Electronics module is corrupt. Reset the device. If the problem persists, replace the Meter Body.
What does it mean when my Honeywell Transmitter is in 'Fixed Current Mode', and how do I change it?
If your Honeywell Transmitter is in 'Fixed Current Mode,' it means the output current is fixed and not varying with the applied input. This can happen if the loop current mode is disabled or if loop test is active. Enable the Loop Current Mode if it is disabled, or exit the Loop Test mode if it is active.
What causes 'Meter Body NVM Corrupt' on a Honeywell Transmitter, and how can I fix it?
If your Honeywell Transmitter displays 'Meter Body NVM Corrupt', it means the Meter Body NVM data has been corrupted. Try resetting the device. If the problem continues, replace the Meter Body.
General| Manufacturer | Honeywell |
|---|---|
| Category | Transmitter |
| Communication Protocol | HART |
| Output | 4-20 mA |
| Ambient Temperature | -40 to 85°C |
| Housing Material | Stainless Steel |
| Pressure Range | Not applicable (Temperature Transmitter) |
| Process Connection | Not applicable (Temperature Transmitter) |
| Material | 316 SS |
| Storage Temperature | -40 to 85°C |
| Protection Rating | IP67 |
Introduction to the ST 700 transmitter family, covering standard and basic models.
Lists protocols, HMI, materials, approvals, and mounting brackets for the ST 700.
Describes the major assemblies: Electronics Housing and Meter Body.
Explains the transmitter's function, output signals, and communication protocols.
Details the information found on the transmitter's model nameplate.
Locates and describes the approvals name plate for compliance information.
Explains how to make zero and span adjustments using assemblies or tools.
Details the characteristics of the Basic and Standard displays.
Lists features and benefits of the 3-button assembly for basic display.
Lists features and capabilities of the 2-button assembly for standard display.
Explains configuration for DE, HART, and Fieldbus protocols.
Details DE mode operation, its characteristics, and advantages.
Explains HART protocol modes (point-to-point, multi-drop) and features.
Introduces tools for configuring HART or DE communication.
Assumes user knowledge of MC Toolkit/MCT404/202 and transmitters.
Refers to another manual for design, installation, and startup details.
Explains prerequisites and potential consequences of using MC Toolkit.
Describes FDC and MC Toolkit applications for transmitter configuration.
Explains the use of MC Toolkit for parameters in a transmitter database.
Details online and offline configuration methods and considerations.
Shows how to connect the MC Toolkit to HART or DE transmitters.
Assumes use of MC Toolkit and lists other supporting tools.
Explains MC Toolkit's online and offline configuration capabilities.
Outlines establishing communication and uploading configuration.
Step-by-step guide to upload configuration from a DE transmitter.
Details configuring Tag ID, Type, Firmware Version, etc.
Covers PV Type, Communication Mode, and FS Direction settings.
Explains LRL, URL, LRV, URV, PV Units, Damping, and Conformity settings.
Covers configuring display units, custom tags, and flow values.
Explains how to view input, output, SV, and communication status.
Describes saving transmitter configuration to a file.
Summarizes features and processes for offline DE configuration.
Explains managing offline configuration files and templates.
Describes downloading offline configurations to a connected transmitter.
Introduces HART configuration using FDC for online and offline tasks.
Assumes user familiarity with MC Toolkit and HART tools.
Explains the FDC homepage links for configuration options.
Customizing FDC for device detection, DD selection, and application settings.
Options for FDC to identify a device using Poll Address or Device TAG.
Configuring FDC to select DD files based on device revision or generic files.
Managing DD files: viewing, adding, or deleting them.
Steps to add a DD file to FDC for a device.
Steps to delete DD files by manufacturer, type, or revision.
Performing configuration, calibration, monitoring, and diagnostics via active link.
Configuring a device offline using a template.
Functions for performing operations on a device with an active link.
Process of detecting and loading a device in FDC.
Navigating the device homepage tabs (Information, Functions, My Views, Tools).
Detailed explanation of each tab on the device homepage.
Performing operations like configuration, calibration, monitoring, and diagnostics.
Lists and describes parameters accessed via Online tab or Shortcuts menu.
Steps to enter or edit the transmitter tag name.
How to change PV units and its effect on LRV/URV.
Procedure to key in LRV and URV values for transmitter calibration.
Setting range values using applied pressure methods.
Saving device configuration snapshot as history for asset management.
Exporting history records to FDM for audit purposes.
Exporting history records to DocuMint.
Creating and modifying custom views for device variables.
Configuring a device offline using a template.
Steps to import offline configuration templates from FDM.
Downloading an offline configuration to an online device.
Discusses transmitter calibration needs and environment.
Recommends bench calibration with MC Toolkit or using TPS system.
Lists necessary test equipment for calibration.
Procedure for calibrating the analog output signal at zero and 100% levels.
Provides procedures for input and output calibration.
Conditions necessary for accurate transmitter input calibration.
Describes the three parts of input calibration: zero, LRV, and URV.
Step-by-step guide to correct input at zero, LRV, and URV.
Procedure for calibrating DE transmitter's analog output.
Preparation steps for DE analog output calibration.
Procedure to manually set PV LRV and URV values.
Steps to reset calibration data to factory default values.
Information on calibrating analog output and range, and resetting calibration.
Discusses calibration needs and recommendations for accuracy.
Lists test equipment needed for HART calibration.
Calibrating the transmitter's analog output at 0% and 100% levels.
Explains two-point calibration for adjusting all points in a range.
Procedure for correcting the Lower Range Value.
Procedure for correcting the Upper Range Value.
Steps to reset calibration data to factory calibrated range.
How to read calibration records for HART devices.
Information on Advanced Diagnostic features of the ST 700 Standard Transmitter.
Lists various diagnostics that can be viewed.
Details how to view and set the device installation date.
Information on Maximum and Minimum PV Tracking diagnostics.
Information on Maximum and Minimum SV Tracking diagnostics.
Information on Maximum and Minimum TV Tracking diagnostics.
Information on Maximum and Minimum ET Tracking diagnostics.
Percent of service life spent in stressful conditions.
Percent of expected service life based on electronics temperature.
Diagnostics for current and minimum operating voltage.
Tracking diagnostics for Sensor Supply Voltage.
Tracking diagnostics for Sensor CPU Temperature.
Diagnostics related to device power-ups and last power fail time.
Lists critical and non-critical HART diagnostic messages.
Describes HART critical and non-critical diagnostic details and resolutions.
Lists and describes DE diagnostics and their resolutions.
Introduces DTMs for ST 700 HART/Fieldbus models on Pactware/FDM.
Lists required components for using HART DTMs.
Provides download links for Pactware, HART DTM, and Honeywell HART DTM Library.
Step-by-step guide to install and run the DTM.
Shows the DTM homepage after selecting parameterization.
Displays overall device status image and link to status screen.
Shows primary variables, gauges, LRV, and URV.
Provides tabs for accessing functions like Setup, Calibration, and Status.
Details parameters on the Basic Setup page like Transfer Fn and Device Info.
Allows selection of Linear or Square Root transfer function.
Allows selection of User Config Mode and breakpoint for signal conditioning.
Provides access to read-only and read/write parameters.
Provides access to calibration methods and records.
Lists available calibration methods like Apply Values, D/A Trim.
How to access calibration records for URV, LRV, Zero Trim, and Reset Corrects.
Graphical representation of process variables and access to trend charts.
Displays trend charts for process variables.
Shows critical/non-critical status and context-sensitive help.
Displays help for critical/non-critical statuses.
Access to Advanced Diagnostics and Config History functions.
Allows configuration of Tamper Alarm and Write Protect mode.
Shows Sensor Limits, Output Condition, Signal Condition, and Burnout levels.
Details material of construction for Meter Body.
Allows configuring the display from the host.
Configures display screens and parameters.
Summary screen showing all parameters.
Opens the offline parameter configuration page.
Lists protocols, HMI, materials, approvals, and mounting brackets for Basic model.
Describes the major assemblies (Electronics Housing, Meter Body) for Basic model.
Explains the Basic transmitter's function and communication protocols.
Details the model number format and identification for Basic transmitter.
Locates and describes the approvals name plate for compliance.
Explains adjustments for Basic transmitter using two-button assembly or tools.
Details the characteristics of the standard display for Basic transmitter.
Lists features and capabilities of the 2-button assembly for Basic model.
Explains HART communication for the Basic transmitter.
Explains HART protocol modes and features for Basic transmitter.
Introduces tools for configuring HART operation for Basic transmitter.
Assumes user knowledge of MC Toolkit/MCT404/202 and Basic transmitters.
Refers to another manual for design, installation, and startup details.
Explains prerequisites and potential consequences of using MC Toolkit for Basic transmitter.
Describes FDC application for HART configuration of Basic transmitters.
Explains use of MC Toolkit for parameters in Basic transmitter database.
Details online and offline configuration methods for Basic transmitter.
Introduces HART configuration using FDC for Basic transmitter.
Explains FDC homepage links for configuration options for Basic transmitter.
Customizing FDC for device detection, DD selection, and settings for Basic transmitter.
Options for FDC to identify a device using Poll Address or Device TAG for Basic transmitter.
Configuring FDC to select DD files for Basic transmitter.
Managing DD files for Basic transmitter.
Steps to add a DD file to FDC for a Basic transmitter.
Steps to delete DD files for Basic transmitter.
Configuring a device offline using a template for Basic transmitter.
Functions for operations on a device with an active link for Basic transmitter.
Process of detecting and loading a device in FDC for Basic transmitter.
Navigating device homepage tabs for Basic transmitter.
Detailed explanation of tabs on the device homepage for Basic transmitter.
Information on calibrating analog output and range for Basic transmitter.
Discusses calibration needs and recommendations for accuracy for Basic transmitter.
Lists test equipment for Basic transmitter calibration.
Calibrating the Basic transmitter's analog output at 0% and 100% levels.
Explains two-point calibration for Basic transmitter range adjustment.
Procedure for correcting the Lower Range Value for Basic transmitter.
Procedure for correcting the Upper Range Value for Basic transmitter.
Steps to reset calibration data to factory default values for Basic transmitter.
How to read calibration records for Basic HART devices.
Information on Advanced Diagnostic features of the ST 700 Basic Transmitter.
Lists various diagnostics that can be viewed for Basic transmitter.
Details how to view and set the device installation date for Basic transmitter.
Information on Maximum and Minimum PV Tracking diagnostics for Basic transmitter.
Information on Maximum and Minimum SV Tracking diagnostics for Basic transmitter.
Information on Maximum and Minimum TV Tracking diagnostics for Basic transmitter.
Information on Maximum and Minimum ET Tracking diagnostics for Basic transmitter.
Lists critical and non-critical HART diagnostic messages for Basic transmitter.
Describes HART critical and non-critical diagnostic details and resolutions for Basic transmitter.
Introduces DTMs for ST 700 Basic HART models on Pactware/FDM.
Lists required components for using HART DTMs for Basic transmitter.
Provides download links for Pactware, HART DTM for Basic transmitter.
Step-by-step guide to install and run the DTM for Basic transmitter.
Shows the DTM homepage after selecting parameterization for Basic transmitter.
Displays overall device status image and link to status screen for Basic transmitter.
Shows primary variables, gauges, LRV, and URV for Basic transmitter.
Provides tabs for accessing functions like Setup, Calibration for Basic transmitter.
Details parameters on the Basic Setup page for Basic transmitter.
Allows selection of Linear or Square Root transfer function for Basic transmitter.
Allows selection of User Config Mode for Basic transmitter.
Provides access to parameters for Basic transmitter.
Provides access to calibration methods and records for Basic transmitter.
Lists available calibration methods for Basic transmitter.
How to access calibration records for Basic transmitter.
Graphical representation of process variables for Basic transmitter.
Shows critical/non-critical status and help for Basic transmitter.
Access to Advanced Diagnostics and Config History for Basic transmitter.
Allows configuration of Tamper Alarm and Write Protect mode for Basic transmitter.
Shows Sensor Limits, Output Condition, Signal Condition for Basic transmitter.
Details material of construction for Meter Body for Basic transmitter.
Allows configuring the display from the host for Basic transmitter.
Configures display screens and parameters for Basic transmitter.
Summary screen showing all parameters for Basic transmitter.
To Next Page