Horizon Hobby Blade 120 S

Questions and Answers

D
David WilliamsAug 21, 2025
Why does my Horizon Hobby Blade 120 S helicopter vibrate in flight?
- J
  Jerry WhiteAug 21, 2025
  If your Horizon Hobby Toy helicopter vibrates or shakes in flight, consider these potential causes and solutions: * Check the main rotor blades, blade grips, main gear, and main shaft for cracks, chips, or missing teeth. Replace any damaged parts. Also, replace any bent spindle. * Ensure that the rotor head linkages are correctly connected to the short ball links on the swashplate.
J
Jessica AcostaAug 25, 2025
What to do if Horizon Hobby Blade 120 S Toy helicopter won't respond to throttle?
- A
  Austin Brown IIAug 25, 2025
  If your Horizon Hobby Toy helicopter will not respond to throttle, there are a couple of potential reasons: * The throttle might be too high, or the throttle trim could be too high. Disconnect the flight battery, place the throttle stick in the lowest position, and lower the throttle trim a few clicks. Then, connect the flight battery and allow the model to initialize. * The helicopter may have moved during initialization. Disconnect the flight battery and re-initialize the helicopter, ensuring it remains still.
Z
Zachary DennisAug 27, 2025
Why Horizon Hobby Blade 120 S drifts in calm winds?
- T
  Terry MooreAug 27, 2025
  If your Horizon Hobby Toy helicopter drifts in calm winds, it could be due to vibration, damaged linkage, or a damaged servo. Under normal operation, the transmitter trims should not require adjustment, as the center positions are memorized during initialization. If trim adjustments are necessary after takeoff, verify the balance of all rotating components, ensure the linkages are not damaged, and make sure the servos are in proper working condition. Perform the Drift Calibration procedure.
G
Garrett ConnerAug 30, 2025
Why Horizon Hobby Blade 120 S Toy has reduced flight time?
- D
  Dana Paul PhDAug 30, 2025
  If your Horizon Hobby Toy helicopter has reduced flight time or seems underpowered, here's what might be happening: * The flight battery charge might be low. Completely recharge it. * The flight battery could be damaged. Replace it, following the battery instructions. * The flight conditions could be too cold. Ensure the battery is warm (room temperature) before use.
J
jorgecooleySep 2, 2025
Why Horizon Hobby Toy has tail oscillation?
- S
  Steven FloresSep 2, 2025
  If your Horizon Hobby Toy helicopter exhibits tail oscillation, wags, or demonstrates poor performance, it could stem from several factors. Verify that the boom is tight and completely inserted into the frame. Inspect the tail rotor for any damage. Confirm that the tail motor mount is secure. Replace any damaged or worn components.
S
shaffermichaelSep 5, 2025
What to do if Horizon Hobby Blade 120 S Toy does not hold level?
- S
  Stephanie WatkinsSep 5, 2025
  If your Horizon Hobby Toy model does not hold level or the panic recovery doesn't level and you notice random movements in flight, it could be due to vibration. Verify the receiver is properly attached to the helicopter. Ensure that no wires are contacting the receiver. Inspect and balance all rotating components. Verify the main shaft and tail rotor adapter are not damaged or bent. Inspect mechanics for broken or damaged parts and replace as necessary.
J
Jeffrey HowardSep 8, 2025
Why does Horizon Hobby Blade 120 S have severe vibration?
- N
  nunezkyleSep 8, 2025
  If your Horizon Hobby Toy experiences severe vibration, it's likely due to a rotating component being out of balance. Check the main shaft, tail rotor, main rotor blades, main frame, and adapter for damage, and replace them as necessary. Minimizing vibration is crucial for the proper functioning of Panic Recovery and Return to Level features.
B
brownadamSep 12, 2025
Why Horizon Hobby Blade 120 S drifts in wind?
- D
  Dawn JamesSep 12, 2025
  The Horizon Hobby Toy model will drift with the wind but should remain level in flight. Simply hold the cyclic stick in the necessary position to keep the model stationary. The model must lean into the wind to remain stationary; if the model remains level, then it will drift with the wind.
S
Sara Gilbert MDNov 14, 2025
What to do if LED flashes rapidly on Horizon Hobby Blade 120 S after binding?
- A
  adam09Nov 15, 2025
  If the LED on the receiver of your Horizon Hobby toy flashes rapidly and the helicopter doesn't respond to the transmitter after binding, there are several potential causes: * There may have been less than a 5-second wait between powering on the transmitter and connecting the flight battery to the helicopter. To resolve this, leave the transmitter powered on, then disconnect and reconnect the flight battery to the helicopter. * The helicopter might be bound to a different model memory (ModelMatch™ transmitters only). Select the correct model memory on the transmitter and reconnect the flight battery. * The flight battery or transmitter battery charge could be too low. Replace or recharge the batteries. * The aircraft or transmitter may be too close to a large metal object, wireles...
H
Heather ObrienNov 17, 2025
What to do if LED flashes rapidly on Horizon Hobby Blade 120 S during binding?
- P
  patricia54Nov 18, 2025
  If the LED on the receiver of your Horizon Hobby Toy flashes rapidly and the aircraft won't respond to the transmitter during binding, it could be due to several reasons: * The transmitter might be too near the aircraft during the binding process. Power off the transmitter, move it further away from the aircraft, disconnect and reconnect the flight battery to the aircraft, and then follow the binding instructions. * The bind switch or button may not have been held while the transmitter was powered on. Power off the transmitter and repeat the bind process, ensuring the bind switch or button is held. * The aircraft or transmitter might be too close to a large metal object, wireless source, or another transmitter. Move the aircraft and transmitter to another location and attempt bindin...

Summary

Safety Precautions and Warnings

Meaning of Special Language

Defines hazard terms (NOTICE, CAUTION, WARNING) used in the manual.

Counterfeit Product Warning

Advises against counterfeit parts for safety and performance.

First Flight Preparation

Li-Po Battery Charging Warnings

Critical safety warnings for charging Li-Po batteries to prevent fire or damage.

Flight Battery Charging Procedure

Step-by-step guide for charging the flight battery, including LED indicators.

Installing Transmitter Batteries

BNF Transmitter Setup

DXe Channel Reversal for Control

How to reverse channel 6 on the DXe transmitter for proper helicopter control.

Transmitter Flight and Panic Control

How flight modes and panic mode are controlled via transmitter switches/buttons.

DX6 i Transmitter Setup Guide

DX6 i Flight and Panic Mode Configuration

Details how to configure Panic Mode and Flight Modes on the DX6i transmitter.

DX7 s Transmitter Setup Guide

DX7 s Flight and Panic Mode Configuration

Details how to configure Panic Mode and Flight Modes on the DX7s transmitter.

DX8 Transmitter Setup Guide

DX8 Flight and Panic Mode Configuration

Details how to configure Panic Mode and Flight Modes on the DX8 transmitter.

Multi-Model Transmitter Setup (DX6, DX7 Gen 2, DX9, DX18)

Flight, Panic, and Channel Setup

Covers F-Mode, Channel Assign, Panic Mode, and Flight Mode for various transmitter models.

Installing the Flight Battery

Battery Polarity and Care Warnings

Warnings about battery polarity, disconnection, and over-discharge to prevent damage.

Transmitter and Receiver Binding

MLP6 DSM RTF Binding Procedure

Step-by-step guide to bind the MLP6DSM transmitter to the RTF helicopter.

General BNF Binding Procedure

RTF Transmitter Controls Overview

Flight Mode and Panic Controls

Explains the function of flight mode and panic recovery controls on the transmitter.

Transmitter Indicators and Rate Adjustment

Describes transmitter LEDs, trim buttons, and dual rate selection for control sensitivity.

Control System Tests

Elevator and Aileron Control Checks

Tests for elevator and aileron controls to ensure proper servo and linkage operation.

Understanding Primary Flight Controls

Throttle and Rudder Control Functions

Explains how throttle and rudder controls affect helicopter movement.

Elevator and Aileron Control Functions

Explains how elevator and aileron controls affect helicopter movement.

SAFE Technology Features

SAFE Technology Operational Benefits

Highlights SAFE benefits: flight envelope protection and multiple flight modes.

Helicopter Flight Operations and Safety

Panic Recovery, Flying, and Landing

Details panic recovery, flying environment, takeoff, hovering, and landing procedures.

Flight Modes and Low Voltage Cutoff

Describes flight modes, LVC function, and battery care after flight.

Helicopter Drift Calibration Procedure

Post-Flight Inspection and Maintenance

Component Inspection and Maintenance Checklist

Covers inspection of ball links, bearings, wiring, fasteners, rotors, and mechanics.

Troubleshooting Guide: Binding and Throttle

DXe Binding and Throttle Response Issues

Addresses DXe binding problems and lack of throttle response.

Troubleshooting Guide: Performance Issues

Flight Time, Vibration, and Control Stability

Solves issues with reduced flight time, vibration, model stability, and panic recovery.

Tail Oscillation, Drift, and Vibration

Addresses tail wag, poor performance, drift in winds, and severe vibration.

Exploded View Diagram of Parts

Helicopter Parts List

Limited Warranty Information and Service

Warranty Coverage, Exclusions, and Remedies

Details warranty scope, exclusions, purchaser's remedies, and liability limits.

Obtaining Warranty and Non-Warranty Service

Explains how to get warranty support, service, or non-warranty service, including contacts.

Warranty and Service Contact Information

Horizon Hobby Contact Details by Country

Provides Horizon Hobby service and support contact information for various countries.

FCC Compliance and RF Exposure

Antenna Separation Distance Requirements

Safety guidelines regarding antenna separation distance to meet RF exposure requirements.

IC Compliance Information

European Union Compliance and Disposal

EU Compliance Statement and WEEE Disposal

Declares compliance with EU directives and provides WEEE disposal guidance for electronic waste.