What does rapidly flashing green LED mean on Horizon Hobby Toy helicopter?
A rapidly flashing green LED on your Horizon Hobby Toy helicopter indicates that the helicopter is in bind mode. Power off both the helicopter and the transmitter, then repeat the binding process.
What does it mean if the green LED is illuminated and the blue LED turns off on Horizon Hobby Toy?
If the green LED is illuminated and the blue LED turns off on your Horizon Hobby Toy, it indicates that the helicopter calibrate function is not activated. Place the helicopter on a level surface and move the calibrate switch to the green position.
What to do if the motor doesn't spin on my Horizon Hobby Toy?
If the motor on your Horizon Hobby Toy does not spin but the servos operate normally, it means the throttle cut function is activated. Set the throttle cut switch to the green dot position.
What does it mean if green and blue LEDs turn off on Horizon Hobby Toy?
If both the green and blue LEDs turn off on your Horizon Hobby Toy, it indicates a battery connection error. Reconnect or replace the battery.
Why is the battery bulging after flight on my Horizon Hobby Toy?
If the battery is bulging after a flight with your Horizon Hobby Toy, it indicates that the battery is damaged and should be replaced.
Why Horizon Hobby Toy doesn't return to level when sticks are centered?
If your Horizon Hobby Toy model does not return to level when the sticks are centered, it could be because the model was not initialized on a level surface, so re-initialize the model on a level surface. Another reason could be that the model was not taken off from a level surface, so always lift off from a level surface.
What does it mean if green LED turns off and the blue LED illuminates on Horizon Hobby Toy?
If the green LED turns off and the blue LED illuminates on your Horizon Hobby Toy, it means the helicopter has lost connection with the transmitter. Rebind the transmitter to the receiver.
Why is my Horizon Hobby Toy helicopter control response inconsistent?
Inconsistent control response or the need for extra trim to neutralize movement in your Horizon Hobby Toy helicopter suggests that the aircraft was not initialized properly. Disconnect the flight battery, center the transmitter control trims, and re-initialize the helicopter.
Why Horizon Hobby Toy helicopter green LED flashes rapidly then goes off during binding?
If the green LED on your Horizon Hobby Toy aircraft flashes rapidly, then goes off and the aircraft won't respond to the transmitter during binding, it could be because the bind switch or button was not held while the transmitter was powered on, so power off the transmitter and repeat the bind process. Another cause could be that the aircraft or transmitter is too close to a large metal object, wireless source, or another transmitter, so move them to another location and attempt binding again.
Why does my Horizon Hobby Toy helicopter have reduced flight time?
Reduced flight time or underpowered performance in your Horizon Hobby Toy helicopter can stem from several causes: a low flight battery charge (completely recharge it), a damaged flight battery (replace it following the instructions), flight conditions being too cold (ensure the battery is warm before use), or debris interfering with rotating parts (clean all rotating parts).
Explains the meaning of different LED light combinations on the charger during the charging process.
Allows adjustment of control sensitivity between high (Hi) and low (Lo) rates for flight control.
Prevents accidental motor operation before flight and provides a quick motor shutoff if the helicopter is out of control.
Details how to use transmitter trim buttons to center controls and adjust flight characteristics for stability.
Describes how throttle stick inputs affect the helicopter's vertical movement (climb/descend).
Explains how rudder stick inputs control the helicopter's yaw (nose left/right).
Details how elevator stick inputs affect the helicopter's forward and backward movement.
Describes how aileron stick inputs control the helicopter's left and right tilting movements.
Guides through calibration, takeoff, hovering, landing, and Low Voltage Cutoff (LVC) procedures.
Details what the warranty covers and lists common exclusions like cosmetic damage or misuse.
Outlines Horizon's obligations for service/replacement and limits liability for consequential damages.
Provides instructions on how to obtain warranty service and contact information for support.
General| Type | Helicopter |
|---|---|
| Brand | Horizon Hobby |
| Model | Blade 150 FX RTF |
| Channels | 6 |
| Gyro | 3-axis |
| Motor Type | Brushless |
| Ready To Fly | Yes |
| Battery | 2S 7.4V LiPo |
| Flight Time | 5 minutes |
| Transmitter | Included |
| Main Rotor Head Type | Flybarless |
| Charger | USB Charger included |
| Main Rotor Diameter | 12.8 in (324 mm) |
| Tail Rotor Diameter | 2.8 in (71mm) |
To Next Page