Hospira Lifecare PCA3 User Manual

430-04684-002 (Rev. 01/06)
System
Operating
Manual
Hospira, Inc., Lake Forest, IL 60045, USA
PCA3NDC.book Page 0 Tuesday, January 10, 2006 2:01 PM

Hospira Lifecare PCA3 Specifications

General

Model	Lifecare PCA3
Device Type	Infusion Pump
Manufacturer	Hospira
Intended Use	Patient-Controlled Analgesia (PCA)
Infusion Modes	PCA, Continuous, PCA with Continuous
Drug Library	Yes (Configurable)
Dosing Units	mL, mg, mcg, units
Dose Increment	Adjustable
PCA Dose	Adjustable
Bolus Dose Range	Adjustable
Maximum Dose Limit	Yes (Configurable)
Alarms	Air-in-line, Occlusion, Syringe Empty, Low Battery
Display	LCD
Power Source	AC power, rechargeable battery
Battery Life	Up to 6 hours at 5 mL/hr
Compliance	IEC 60601-1
Syringe Size Compatibility	Various syringe sizes (typically 10mL, 20mL, 30mL, 50mL, 60mL)
Dose Rate	0.1 - 1200 mL/hr (depending on syringe size)
Continuous Rate Range	0.1 - 1200 mL/hr (depending on syringe size)

Summary

Descriptive Information

Product Description

Details the LifeCare PCA 3 Infusion System, its features, and components.

Indications for Use

Explains the approved uses and patient suitability for the PCA 3 Infusion System.

Contraindications For Use

Lists conditions and situations where the PCA 3 Infusion System should not be used.

Conventions

Defines formatting conventions used in the manual, such as italics, bold, and brackets.

Definitions (General and Clinical)

Provides definitions for important terms used in the manual, covering general and clinical aspects.

Precautions

Outlines important precautions for safe operation, handling, and potential hazards.

Principles of Operation

Features

Details the main features of the PCA 3 Infusion System, including drug recognition and modes of delivery.

Administration Equipment

Lists and describes the administration sets and catheters compatible with the PCA 3 Infusion System.

Printer Kits

Describes the available printer kits for the PCA 3 Infusion System, including components.

Equipment Description

Components

Identifies and illustrates the main components of the PCA 3 Infusion System's front panel.

Operating Buttons & Keys

Explains the function of each button and key on the PCA 3 Infusion System's control interface.

Basic Operation

Getting Started

Provides step-by-step instructions for the initial setup and unpacking of the PCA 3 Infusion System.

Operating the PCA 3

Details the procedures for operating the PCA 3 Infusion System for intravenous and epidural administration.

Loading Vial

Guides the user through the process of loading a vial into the PCA 3 Infusion System.

Adjusting Settings

Explains how to adjust various settings on the PCA 3, such as alarm volume and display contrast.

Guided Start-Up for Prefilled vials

Step-by-step guide for initiating operation with Hospira prefilled drug vials.

Guided Start-Up for Custom Vials

Step-by-step guide for initiating operation with custom-filled drug vials.

Select Mode

Modes of Delivery

Describes the three primary modes of analgesia delivery: PCA Only, Continuous, and PCA+Continuous.

Programming PCA Only

Provides instructions for programming the PCA 3 Infusion System in the PCA Only mode.

Continuous Mode

Details the steps for programming the PCA 3 Infusion System in Continuous mode.

PCA + Continuous Mode

Explains how to program the PCA 3 Infusion System for PCA + Continuous mode delivery.

Protocols

Information on using pre-programmed protocols for Hospira prefilled vials, set via Service Mode.

Dose Limit (1 or 4 hour)

Explains how to set and manage 1-hour or 4-hour dose limits for patient safety.

Using Review Screens

Describes how to use review screens to verify programmed settings before securing the device.

Changing Settings During Setup

Instructions for modifying programmed settings during the initial setup phase of the PCA 3.

Stopping Infusion or Turning Pump OFF

Details the steps for safely stopping an infusion or turning off the PCA 3 pump.

Making Changes After Setup

Explains how to review, change, or clear settings after the initial setup is complete.

Checking History & Settings

Describes how to check the device's history and current settings, and how to print this information.

Printer Setup

Guides the user through the setup process for connecting and configuring a serial printer.

Printing Event History Log

Instructions on how to print the event history log from the PCA 3 Infusion System.

Downloading to a PC

Details the process for downloading data from the PCA 3 Infusion System to a personal computer.

History and Event Log

Explains the types of data stored in the History and Event Log and how they are presented.

Troubleshooting

Status Messages

Defines the various status messages displayed by the PCA 3 Infusion System.

Pump Alarm System

Explains how the PCA 3 pump alarm system functions and the actions taken during an alarm condition.

Silencing an Alarm

Provides instructions on how to silence alarms, clear causes, and resume operation.

Alarms and Messages

A comprehensive table detailing alarm messages, their causes, and corrective actions.

Maintenance

Pump Storage

Guidelines for storing the PCA 3 Infusion System to prolong its life and maintain functionality.

Cleaning and Sanitizing

Detailed instructions and recommended solutions for cleaning and sanitizing the PCA 3 Infusion System.

Battery Maintenance

Information on maintaining the battery, its charging, lifespan, and replacement considerations.

Specifications

Stored Occlusion Volume

Details the volume stored by the device during an occlusion event.

Time from Occlusion to Alarm

Specifies the time delay between an occlusion event and the system alarm.

Delivery Rate Accuracy

Provides accuracy specifications for the delivery rate of the PCA 3 Infusion System.

Trumpet Curves

Presents graphical data illustrating delivery rate deviation and performance characteristics.

Prescription Delivery Limits

Warranty