Hotpoint H2IHKD526UK Daily Reference Guide

8 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

1

EN

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

PRODUCT DESCRIPTION

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING AHOTPOINT PRODUCT.

In order to receive amore complete assistance, please

register your appliance on: www.hotpoint.eu/register

You can download the Safety Instructions and the User

Manual, by visiting our website docs.hotpoint.eu and

following the Instructions on the back of this booklet.

1. ON-OFF/Reset button with indicator light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time indicator

6. Tablet indicator light

7. Display

8. Half Load indicator lights

9. Half Load button

10. Delay button

11. START/Pause button with indicator light / Tablet (Tab)

CONTROL PANEL

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

1 2 3 4 5 6 7 8 9 10

11

0000 000 00000

Service:

1

2

3

4

5

6

10

12

7

11

9

8

Table of Contents

Other manuals for Hotpoint H2IHKD526UK

Quick Guide4 pages

Questions and Answers:

A
Allison JonesAug 15, 2025
Why is my Hotpoint Dishwasher not filling with water?
- K
  Kathleen KaneAug 16, 2025
  If your Hotpoint Dishwasher isn't filling, it could be due to a few reasons. First, ensure that there is water in the water supply and that the tap is fully open. Another possible cause is a bent inlet hose; make sure the inlet hose is not bent, then reprogram the dishwasher and reboot it. Finally, the sieve in the water inlet hose might be clogged. After checking and cleaning it, turn the dishwasher off and on, then restart a new program.
L
Lori NunezAug 18, 2025
What to do if my Hotpoint Dishwasher does not start or respond to commands?
- A
  Allison LopezAug 18, 2025
  If your Hotpoint dishwasher doesn't start or respond, here are a few things to check: * Make sure the dishwasher is properly plugged into the socket. * If there was a power outage, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds (the dishwasher doesn't restart automatically after a power failure). * Ensure the dishwasher door is fully closed until you hear a click. * If the door was opened for more than 4 seconds during a cycle, press START/Pause and close the door within 4 seconds. * If the display shows 9 or 12 and the On/Off LED is blinking rapidly, turn the appliance off and on again. If the problem continues, unplug the dishwasher for 1 minute, then plug it back in.
C
Christina JohnsonAug 21, 2025
What to do if my Hotpoint Dishwasher drains but the On/Off LED is blinking rapidly?
- J
  Jessica VelezAug 21, 2025
  If your Hotpoint dishwasher drains but the On/Off LED is blinking rapidly, it could be due to several reasons: * The wash cycle might not be finished yet; wait until it completes. * The drain hose could be bent; ensure it is not. * The sink drain pipe might be blocked; clean it. * The filter might be clogged with food residues; clean the filter.
E
Emily HansenAug 25, 2025
What to do if my Hotpoint H2IHKD526UK Dishwasher does not fill with water but shows: On/Off LED is blinking rapidly?
- M
  Michael BaxterAug 25, 2025
  If your Hotpoint dishwasher is not filling with water and the On/Off LED is blinking rapidly, it could be due to: * Lack of water supply or the tap being closed; ensure there is water in the supply and the tap is open. * A bent inlet hose; make sure the hose isn't bent. Reprogram the dishwasher and reboot. * A clogged sieve in the water inlet hose; clean it. After cleaning, turn the dishwasher off and on, then restart a new program.
R
Rachel ThompsonAug 27, 2025
Why are the dishes not clean in my Hotpoint Dishwasher?
- R
  Ryan BradyAug 27, 2025
  If your Hotpoint dishwasher is not cleaning dishes properly, consider the following: * Ensure the crockery is arranged correctly so that the spray arms can rotate freely. * Select a more appropriate wash cycle. * Make sure you are using the correct amount of detergent and that it is suitable for dishwashers. * Ensure the cap on the rinse aid compartment is shut correctly. * Clean the filter assembly if it is soiled or clogged. * Fill the salt reservoir if it is empty.
N
Nathan WadeAug 30, 2025
What to do if my Hotpoint H2IHKD526UK cycle prematurely finishes?
- D
  Douglas RivasAug 30, 2025
  If your Hotpoint Dishwasher cycle is finishing too early, here are a couple of things to check: 1. Ensure the drain hose is positioned at the correct height and is not siphoning into the home sewage system. If siphoning is occurring, install an air admittance valve. 2. Check the water supply for any leaks or issues that might be allowing air to enter.
V
Vincent MillerSep 2, 2025
What to do if my Hotpoint H2IHKD526UK finishes prematurely but shows: On/Off LED is blinking rapidly?
- M
  Matthew HernandezSep 2, 2025
  If your Hotpoint dishwasher is finishing prematurely and the On/Off LED is blinking rapidly, it might be because: * The drain hose is positioned too low or siphoning into the home sewage system; check the height of the drain hose. Install an air admittance valve if siphoning is occurring. * There is air in the water supply; check for leaks or other issues.
S
Shawn GraySep 5, 2025
Why is my Hotpoint Dishwasher making excessive noise?
- T
  Teresa ParrishSep 5, 2025
  Your Hotpoint dishwasher might be making excessive noise due to: * Dishes rattling against each other; make sure to position the crockery correctly. * Too much foam; ensure the detergent is measured correctly and is suitable for dishwashers. Restart the current cycle without adding any detergent.
C
Cheyenne SimonSep 8, 2025
Why is the salt indicator lit on my Hotpoint H2IHKD526UK Dishwasher?
- S
  Stephanie HolmesSep 8, 2025
  The salt indicator light on your Hotpoint dishwasher may be on because the salt reservoir is empty. Refill it with salt. Note that the indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness setting.
C
Crystal BaileySep 12, 2025
Why is the rinse aid indicator lit on my Hotpoint H2IHKD526UK?
- J
  johnsonmadisonSep 12, 2025
  The rinse aid indicator light on your Hotpoint dishwasher may be on because the rinse aid dispenser is empty. Refill the dispenser with rinse aid.

Hotpoint H2IHKD526UK Specifications

General

Appliance type	Dishwasher
Energy Consumption per 100 cycles	85 kWh
Water Consumption per Cycle	9.5 L
Number of Place Settings	13
Control Type	Electronic
Rinse Aid Indicator	Yes
Salt Indicator	Yes
Cutlery Basket	Yes
Quick Wash	Yes
Half Load Option	Yes
Delay Start	Yes
Height	82 cm
Width	60 cm

Related product manuals

Hotpoint H2I HD526 B UK

Hotpoint H2F HL626 UK

Preview: Hotpoint HDA180

Hotpoint HDA180

Hotpoint HDA400

Hotpoint HDA100

Preview: Hotpoint HDA2100

Hotpoint HDA2100

Hotpoint HDA1000

Hotpoint HDA2100H

Preview: Hotpoint HFC3C26WCUK

Hotpoint HFC3C26WCUK

Hotpoint H7F HP43 X UK

Hotpoint HFO 3T241 WFG X