What to do if my HotSpring Hot Tub is causing eye irritation?
Eye irritation from your HotSpring Hot Tub can be caused by: * Low pH: Adjust the pH. * Low sanitizer level: Shock the spa with sanitizer and maintain the sanitizer level.
How to fix a HotSpring MOTO-MASSAGE jet that is inoperative?
If the MOTO-MASSAGE jet in your HotSpring Hot Tub is inoperative or erratic, it could be due to: * Closed AIR CONTROL valves: Open the AIR CONTROL lever. * Clogged filter: Clean the filter.
How to fix HotSpring Hot Spot Stride pump that is operating but not flowing water from jets after refill?
If, after filling or refilling your HotSpring Hot Tub, a jet pump is operating but no water is flowing from the jets, the pump may not be properly primed. Here’s how to resolve it: 1. Turn off power to the spa at the breaker and remove the equipment compartment door. 2. Loosen the union on the top of the pump to allow air to escape, then hand-tighten the union. 3. Turn the power back on, activate the pump, and ensure the union is tight enough to prevent leaks. Re-install the pump and equipment doors. Alternatively, remove and reinstall the FROG cap.
What to do if my HotSpring Hot Spot Stride has skin irritation or rash?
Skin irritation or rash from your HotSpring Hot Tub can be caused by: * Unsanitary water: Shock the spa with sanitizer and maintain the sanitizer level. * Free chlorine level above 5 ppm: Allow the free chlorine level to drop below 5 ppm before using the spa.
Essential guidelines for safe spa operation and user protection.
Measures to prevent unauthorized access and ensure child safety in the spa.
Guidelines to prevent electrical shock, including grounding and RCD use.
Advice for users taking medication or with pre-existing health conditions.
Warnings about overheating and skin burn risks from hot spa water.
Key do's and don'ts for using and maintaining your spa.
Approved cleaning agents and methods for the spa's acrylic shell.
Overview of jets, controls, and features for specific spa models.
Overview of jets, controls, and features for SX and TX spa models.
Essential checks and preparations before filling the spa with water.
Steps for filling the spa and initial system checks.
Steps for filling, adjusting water chemistry, and sanitizing.
Verifying jet operation and priming the spa pumps.
Setting temperature and installing the FROG cartridge.
Step-by-step guide to prime spa pumps if water is not flowing.
Principles of water care, chemical safety, and adding chemicals.
Understanding water parameters: CH, TA, and pH.
Details on FROG, Chlorine, Ozone, and EverFresh systems.
Optional additives for mineral balance and foam control.
Definitions of common terms used in water maintenance.
Description of the control panel, modes, and basic operations.
How to operate temperature, jets, and spa lighting.
Using System Mode, Sleep Mode, and locking spa functions.
Controlling the optional wireless audio system: pairing, volume, sources.
Details of jets connected to Jet Pump 1 for the Relay model.
Details of jets connected to Jet Pump 2 for the Relay model.
Details of jets connected to Jet Pump 1 for the Rhythm model.
Details of jets connected to Jet Pump 2 for the Rhythm model.
Details of all jets and their configurations for the Propel model.
Details of all jets and their configurations for the Stride model.
Details of jets and their configurations for the SX model.
Details of jets and their configurations for the TX model.
Procedures for draining, refilling, and preventing freezing.
Steps for winterizing and opening a spa for seasonal use.
Cleaning and maintaining the spa's filter system and screens.
Cleaning and maintaining spa pillows, exterior, and acrylic shell.
Cleaning the spa cabinet and maintaining the vinyl cover.
How to operate the vinyl cover with a lifter system.
Important safety precautions for spa electrical connections.
Steps for connecting the spa's electrical service and conduit.
Key considerations for choosing and preparing the spa installation site.
Requirements for installing spas outdoors, on decks, or indoors.
How to prepare the spa for leveling and ensure proper drainage.
Information on delivery requirements and ground preparation.
Overview of spa servicing and when to contact a technician.
Troubleshooting for RCD trips and high limit thermostat problems.
Acts invalidating warranty, disclaimers, and customer service.
Common problems and solutions for spa operation issues.
Troubleshooting common water quality and maintenance issues.
Step-by-step guide for removing the spa's door panels.
Step-by-step guide for reinstalling the spa's door panels.
To Next Page
General