Hotsy 5735SS Service Manual (English)

Other manuals for Hotsy 5735SS

Questions and Answers:

R
Russell McculloughAug 14, 2025
What to do if my Hotsy 5735SS runs but won't spray?
- J
  Jeffrey Russo Jr.Aug 15, 2025
  If your Hotsy Pressure Washer runs but won't spray, make sure to squeeze the trigger of the trigger gun. Check that the water supply is turned on by opening the water supply valve. Inspect the pressure nozzle for clogs and clean it if needed. Also, check the inlet water screen for any blockage and clean it if necessary. Lastly, ensure the pump isn't sucking air by filling the detergent container and checking for loose hose clamps or fittings.
S
Shane MccoyAug 18, 2025
Why is the spray pressure low on my Hotsy 5735SS Pressure Washer?
- J
  James HerreraAug 18, 2025
  To address low spray pressure at the nozzle of your Hotsy Pressure Washer, fully open the faucet to ensure an adequate water supply. Inspect the hose for any kinks or damage, and use a 5/8" minimum hose. Check the inlet screen for any debris that may be causing a clog. Additionally, inspect the pressure nozzle for partial clogs or damage, and clean or replace it as needed. Finally, if air is being drawn through the detergent inlet line, refill the detergent container and ensure that the pick-up screen is fully immersed.
J
jesse97Aug 21, 2025
How to resolve poor detergent flow in my Hotsy 5735SS Pressure Washer?
- K
  Kara GordonAug 21, 2025
  If you're experiencing poor or no detergent flow with your Hotsy Pressure Washer, start by refilling the detergent container, ensuring the pick-up screen is fully immersed, and that the container is at or above the level of the pump. Check the detergent screen or hose for clogs and clean them, always starting with a clean detergent container. Also, inspect the detergent injector check valve for clogs and clean it.
K
Kristen SpencerAug 25, 2025
Why is my Hotsy 5735SS not producing hot water?
- V
  vtorresAug 25, 2025
  If your Hotsy Pressure Washer isn't producing hot water, first ensure the burner switch is in the ON position. Next, check that the gas valve switch is also in the ON position. Verify that there is an adequate fuel supply. Finally, confirm that the pump switch is turned on, as the pump must be running before the burner will light.
L
Lawrence PerezAug 28, 2025
How to fix a Hotsy 5735SS Pressure Washer that will not run?
- J
  John BrownAug 28, 2025
  If your Hotsy Pressure Washer won't run, first ensure the pump switch is in the ON position. Check that the power supply is properly connected. Also, inspect the fuse or circuit breaker in the electrical supply line and replace or reset if necessary, making sure to use circuits of adequate capacity. Finally, if the motor circuit is overloaded, allow it to cool down before placing the pump switch in the ON position.
C
Cristian Dean DVMAug 31, 2025
What causes the unloader to cycle on my Hotsy Pressure Washer?
- M
  Matthew HarrisAug 31, 2025
  If your Hotsy Pressure Washer's unloader cycles when the trigger gun is opened or closed, try opening and closing the trigger gun several times to remove air from the system. If the issue persists, the unloader may be defective and need replacement. Also, check for water leaks between the unloader valve and the trigger gun, inspecting fittings, hose, and the trigger gun itself for leaks, and repair or replace any damaged components.
M
Mrs. Brittany DeckerSep 3, 2025
Why is my Hotsy 5735SS providing poor cleaning results?
- J
  Jeffrey StokesSep 4, 2025
  If your Hotsy Pressure Washer is not cleaning effectively, ensure you are mixing the detergent per the manufacturer's instructions and that powdered detergents are fully dissolved. Verify that you are using the correct detergent for the specific cleaning application. Check that the detergent valve is opening properly, and that the handle or knob is not slipping on the shaft.
B
Benjamin RobinsonSep 7, 2025
Why is the pressure relief valve leaking on my Hotsy 5735SS Pressure Washer?
- D
  Dr. Gregory Miller MDSep 7, 2025
  If the pressure relief valve on your Hotsy Pressure Washer is leaking, it could be due to excessive pressure from a defective unloader valve, which would need replacement. Alternatively, the relief valve itself might be defective and require replacement. Another possibility is a dirty relief valve, in which case you should clean the relief valve seat.
R
Rebecca SpearsSep 10, 2025
What causes an uneven spray pattern in my Hotsy 5735SS Pressure Washer?
- G
  glengallagherSep 12, 2025
  If your Hotsy Pressure Washer has an uneven spray pattern, the most likely cause is a partially clogged or damaged pressure nozzle. Try cleaning the nozzle first, and if the problem persists, replace it.