Hotsy 5832SS-208 Service Manual

30 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

GAS-FIRED SERIES

SERVICE MANUAL

For technical assistance or the dealer nearest you consult our web page at

www.hotsy.com

5700/5800

8.916-832.0

■ 5832SS-208 ■ 5832SS ■ 5835SS ■ 5836SS

■ 5732SS-208 ■ 5732SS ■ 5735SS ■ 5736SS

H

O

N

E

Y

W

E

L

L

L

O

H

I

C

H

A

UD

!

C

H

A

U

D

!

8916832-1

Table of Contents

Other manuals for Hotsy 5832SS-208

Operator's Manual30 pages

Questions and Answers:

D
Derek PrinceAug 15, 2025
What to do if my Hotsy Pressure Washer runs but won't spray?
- J
  Jamie JenningsAug 15, 2025
  If your Hotsy Pressure Washer runs but won't spray, make sure to squeeze the trigger of the trigger gun. Check that the water supply is turned on by opening the water supply valve. Inspect the pressure nozzle for clogs and clean it if needed. Also, check the inlet water screen for any blockage and clean it if necessary. Lastly, ensure the pump isn't sucking air by filling the detergent container and checking for loose hose clamps or fittings.
M
Mrs. Catherine Hampton DDSAug 18, 2025
Why is the spray pressure low on my Hotsy 5832SS-208 Pressure Washer?
- J
  Jeanne WagnerAug 18, 2025
  To address low spray pressure at the nozzle of your Hotsy Pressure Washer, fully open the faucet to ensure an adequate water supply. Inspect the hose for any kinks or damage, and use a 5/8" minimum hose. Check the inlet screen for any debris that may be causing a clog. Additionally, inspect the pressure nozzle for partial clogs or damage, and clean or replace it as needed. Finally, if air is being drawn through the detergent inlet line, refill the detergent container and ensure that the pick-up screen is fully immersed.
W
Wayne CarterAug 22, 2025
How to resolve poor detergent flow in my Hotsy Pressure Washer?
- Y
  Yvette GriffinAug 22, 2025
  If you're experiencing poor or no detergent flow with your Hotsy Pressure Washer, start by refilling the detergent container, ensuring the pick-up screen is fully immersed, and that the container is at or above the level of the pump. Check the detergent screen or hose for clogs and clean them, always starting with a clean detergent container. Also, inspect the detergent injector check valve for clogs and clean it.
B
Brandy HicksAug 26, 2025
Why is my Hotsy Pressure Washer not producing hot water?
- R
  Robert BurchAug 26, 2025
  If your Hotsy Pressure Washer isn't producing hot water, first ensure the burner switch is in the ON position. Next, check that the gas valve switch is also in the ON position. Verify that there is an adequate fuel supply. Finally, confirm that the pump switch is turned on, as the pump must be running before the burner will light.
T
teresawallaceAug 28, 2025
How to fix a Hotsy Pressure Washer that will not run?
- F
  fosteremilyAug 28, 2025
  If your Hotsy Pressure Washer won't run, first ensure the pump switch is in the ON position. Check that the power supply is properly connected. Also, inspect the fuse or circuit breaker in the electrical supply line and replace or reset if necessary, making sure to use circuits of adequate capacity. Finally, if the motor circuit is overloaded, allow it to cool down before placing the pump switch in the ON position.
T
tfisherAug 31, 2025
What causes the unloader to cycle on my Hotsy 5832SS-208?
- E
  Eric BoydSep 1, 2025
  If your Hotsy Pressure Washer's unloader cycles when the trigger gun is opened or closed, try opening and closing the trigger gun several times to remove air from the system. If the issue persists, the unloader may be defective and need replacement. Also, check for water leaks between the unloader valve and the trigger gun, inspecting fittings, hose, and the trigger gun itself for leaks, and repair or replace any damaged components.
U
uwalkerSep 4, 2025
Why is my Hotsy 5832SS-208 providing poor cleaning results?
- C
  Christina SmithSep 4, 2025
  If your Hotsy Pressure Washer is not cleaning effectively, ensure you are mixing the detergent per the manufacturer's instructions and that powdered detergents are fully dissolved. Verify that you are using the correct detergent for the specific cleaning application. Check that the detergent valve is opening properly, and that the handle or knob is not slipping on the shaft.
S
Sara SimmonsSep 8, 2025
Why is the pressure relief valve leaking on my Hotsy Pressure Washer?
- U
  uleeSep 8, 2025
  If the pressure relief valve on your Hotsy Pressure Washer is leaking, it could be due to excessive pressure from a defective unloader valve, which would need replacement. Alternatively, the relief valve itself might be defective and require replacement. Another possibility is a dirty relief valve, in which case you should clean the relief valve seat.
W
Willie DanielSep 12, 2025
What causes an uneven spray pattern in my Hotsy 5832SS-208 Pressure Washer?
- K
  Kimberly SmithSep 12, 2025
  If your Hotsy Pressure Washer has an uneven spray pattern, the most likely cause is a partially clogged or damaged pressure nozzle. Try cleaning the nozzle first, and if the problem persists, replace it.

Hotsy 5832SS-208 Specifications

General

Model	5832SS-208
Pressure	3000 PSI
Voltage	208V
Weight	695 lbs
Dimensions	54"L x 31"W x 49"H
Amps	20
Power Source	Electric
Phase	3
Max Pressure	3000 PSI
Pump Type	Triplex Plunger
Pump Material	Brass Manifold
Thermal Relief Valve	Yes
Flow Rate	4 GPM
GPM	4.0
Max Flow Rate	4 GPM

Related product manuals

Preview: Hotsy 555SS

Preview: Hotsy 560SS

Preview: Hotsy 555HE

Preview: Hotsy 555 HE

Hotsy 952SS-208

Preview: Hotsy 1800 Series

Hotsy 1800 Series