The Hover-1 Drive is an electric hoverboard designed for personal transportation. It utilizes digital electronic gyroscopes and acceleration sensors to control balance and motion, responding to the user's center of gravity. The device also incorporates a control system to operate motors located within the wheels. A built-in inertia dynamic stabilization system aids in balance when moving forward and backward, but not during turns. To enhance stability during turns, especially at higher speeds, users should shift their weight to counteract centrifugal force.
Before operating the Hover-1 Drive, it is crucial to read the entire operation manual thoroughly. Failure to follow basic instructions and safety precautions can result in damage to the hoverboard, other property, serious bodily injury, or even death. Always wear a properly fitted helmet that complies with CPSC or CE safety standards when riding.
Key Safety Instructions:
- Keep the Drive away from heat sources, direct sunlight, humidity, water, and other liquids.
- Do not operate if exposed to water, moisture, or other liquids to prevent electric shock, explosion, or injury.
- Do not use if the Drive has been dropped or damaged.
- Repairs to electrical equipment should only be performed by the manufacturer; improper repairs void the warranty and pose serious risks.
- Do not puncture or harm the exterior surface.
- Keep the Drive free from dust, lint, etc.
- Use the Drive only for its intended purpose.
- This product is not a toy and should be kept out of reach of children.
- Do not expose batteries to excessive heat, direct sunlight, or open flame.
- Prevent hands, feet, hair, body parts, clothing, or similar articles from contacting moving parts, wheels, or the drivetrain while the Drive is running.
- Do not operate or allow others to operate until all instructions, warnings, and safety features in the manual are understood.
- Consult a doctor if you have medical conditions that could affect your ability to use the Drive.
- Persons with head, back, neck ailments, or prior surgeries to those areas are not recommended to use the Drive.
- Do not operate if pregnant or if you have a heart condition.
- Individuals with mental or physical conditions that may impair their ability to understand and perform safety instructions should not use the Drive.
- Always keep your serial number for warranty claims and proof of purchase.
- Prolonged exposure to UV rays, rain, and elements can damage enclosure materials; store indoors when not in use.
Low Temperature Warning:
Low temperatures affect the lubrication of moving parts, increasing internal resistance and significantly decreasing battery discharge capacity. Exercise caution when riding in cold temperatures (below 40°F/4°C), as this can increase the risk of mechanical failures, leading to damage, injury, or death.
Package Contents:
- Hover-1 Drive Hoverboard
- Charger & Charging Cable
- Operation Manual
Features/Parts:
- Fender
- Right Foot Mat
- Battery Indicator
- Left Foot Mat
- Tire
- Charge Port (Located in Rear)
- Power Button (Located in Rear)
- Protective Chassis Casing
Technical Specifications:
- Model: H1-DRIVE
- Net Weight: 14.45 lbs (6.55 kg)
- Max Supported Weight: 160 lbs (72.5 kg)
- Min Supported Weight: 44 lbs (20 kg)
- Motor: 320W (dual 160W motors)
- Max Speed: Up to 7 mph (11.3 km/h)
- Max Range: Up to 3 miles (4.8 km)
- Max Incline Angle: 10°
- Minimum Turning Radius: 0°
- Charge Time: Up to 6 hours
- Battery Type: Lithium-ion
- Battery Voltage: 36V
- Battery Capacity: 2Ah
- Power Requirement: AC 100V-240V, 50Hz/60Hz
- Ground Clearance: 1.5 Inches (3.81 cm)
- Platform Height: 4.5 Inches (11.43 cm)
- Tire Size: 6.5 Inches (16.51 cm)
- Tire Type: Non-Pneumatic Solid Tires
- UL Certification: UL2272 certified
Controls and Display:
- Turning On/Off: Place the Drive flat on the floor, press the power button (rear of Drive) once. The LED indicator (center of Drive) will light up, indicating power on. Press the power button once to turn off.
- Mat Sensors: Four sensors are located under the foot mats. Ensure you step on the foot mats when riding; avoid stepping on other areas. Applying weight to only one foot mat may cause vibration or spinning.
- Battery Indicator: Located in the middle of the Drive.
- Green LED: Fully charged.
- Red flashing LED with beeping: Low battery.
- Yellow flashing LED: Charging.
- Recharge when the LED turns red.
- Running Indicator: Lights up when foot mats are triggered, indicating the hoverboard is in running state. Turns red during an error (see "SAFETY ALERTS").
Before Riding:
- Understand all functions of your Drive.
- Practice at slower speeds in a flat, open area before public use.
- Pre-Ride Checklist: Ensure the Drive is in proper working order. Contact Customer Support for any malfunctions.
- Warning: Do not ride a damaged Drive; replace damaged parts before use.
- Ensure the battery is fully charged.
- Wear appropriate safety gear.
- Wear comfortable clothes and flat, closed-toe shoes.
Safety Precautions (Continued):
- Check local laws regarding electric transportation devices on public roads.
- Hover-1 is not liable for tickets or violations due to non-compliance with local laws.
- Always wear a CPSC or CE certified helmet.
- Obey all local traffic laws (lights, one-way streets, stop signs, crosswalks).
- Ride with traffic.
- Ride defensively; expect the unexpected.
- Give pedestrians the right-of-way.
- Do not ride too close to pedestrians; alert them when passing.
- Slow down at intersections and look both ways before crossing.
- The hoverboard lacks reflectors; riding in low-visibility conditions is not recommended.
- Warning: In low-visibility conditions (fog, dusk, night), wear bright, reflective clothing to prevent collisions.
- Do not ride above your skill level; practice all functions.
- Before stepping on, ensure the Drive is flat on level ground, powered on, and the running indicator is green. Do not step on if red.
- Do not open or modify the Drive; this voids the warranty and can cause failure, injury, or death.
- Do not use the Drive in a manner that endangers people or property.
- Maintain a safe distance from others.
- Keep feet on foot mats at all times; moving feet off can be dangerous.
- Do not operate under the influence of drugs or alcohol.
- Do not operate when restless or sleepy.
- Do not ride off curbs, ramps, or like a skateboard; avoid skate parks or empty pools. Misuse voids warranty and can lead to injury.
- Avoid continuous spinning in place, as it causes dizziness and increases injury risk.
- Do not abuse the Drive; physical abuse (e.g., dropping) voids the warranty.
- Do not operate in or near puddles, mud, sand, stones, gravel, debris, or rough terrain.
- Use on flat, even paved surfaces. Lift over uneven pavement or obstructions.
- Do not ride in inclement weather (snow, rain, hail, sleet, icy roads) or extreme heat/cold.
- Bend knees on bumpy/uneven pavement to absorb shock and maintain balance.
- If unsure about safe terrain, dismount and carry the Drive.
- Do not attempt to ride over bumps or objects greater than ½ inch.
- Pay attention to road conditions, people, property, and objects.
- Do not operate in crowded areas.
- Exercise extreme caution indoors, especially around people, property, and narrow spaces.
- Do not operate while talking, texting, or looking at your phone.
- Do not ride where prohibited.
- Do not ride near motor vehicles or on public roads.
- Do not travel up or down steep hills.
- Intended for single individual use; do not operate with two or more people.
- Do not carry anything while riding.
- Individuals with lack of balance should not operate.
- Recommended for riders ages 8 and older.
- Allow longer stopping distances at higher speeds.
- Do not step forward off the Drive.
- Do not attempt to jump on or off.
- Do not attempt stunts or tricks.
- Do not ride in dark or poorly lit areas.
- Do not ride off-road, near potholes, cracks, or uneven pavement.
- Be aware you are 4.5 inches (11.43 cm) taller when operating; clear doorways safely.
- Do not turn sharply, especially at high speeds.
- Do not step on the fenders.
- Avoid riding in unsafe places with flammable gas, steam, liquid, dust, or fiber.
- Do not operate near swimming pools or other bodies of water.
- Warning (Kart Attachment): When using with a kart attachment (sold separately), do NOT ride uphill on inclines above 5-10°. A safety mechanism will shut down the hoverboard. Dismount, place on a flat surface, wait 2 minutes, then power on again.
- Warning (Adult Supervision): Adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools, or other bodies of water. Always wear shoes and allow only one rider at a time.
Riding Your Drive:
- Familiarize yourself with operating procedures before use.
- Ensure the Drive is fully charged before initial use.
- Mounting: Stand directly behind the Drive, place one foot on a foot mat, keeping weight on the ground. Shift weight to the foot on the Drive, then quickly and evenly step on with the other foot.
- Notes: Stay relaxed, step on quickly and confidently. It's normal for the hoverboard to vibrate or spin if weight is applied to only one foot mat.
- Find your center of gravity. Standing straight up stops the device. Tilt your center of gravity in the desired direction to move.
- Turning: Apply pressure to the right foot to turn right, and to the left foot to turn left.
- Warning: Do not turn sharply or at high speeds. Avoid riding quickly along slopes, as it may cause injury.
- Bend knees for bumps/uneven surfaces; dismount and carry to a safe surface if necessary.
- Dismounting: From a stopped position, lift your dominant leg and step down behind you (STEP BACK). Then, step off with the other foot.
- Warning: Lift feet completely off the foot mat when stepping back to dismount to avoid a tailspin.
Speed and Weight Limitations:
- Maximum Speed: 7 mph
- Maximum Weight: 160 lbs
- Minimum Weight: 44 lbs
- Warning: Exceeding weight limits increases the possibility of injury or product damage.
- Notes: When max speed is reached, the Drive will beep and slowly tilt the rider back to prevent injury.
Operating Range:
The Drive can travel up to 3 miles on a full charge under ideal conditions. Factors affecting range:
- Terrain: Smooth, flat surfaces yield highest range. Uphill or rough terrain reduces range.
- Weight: Lighter users achieve higher range.
- Ambient Temperature: Ride and store in recommended temperatures for optimal range and battery life.
- Speed and Riding Style: Moderate, consistent speed maximizes range. High speeds, frequent starts/stops, and idling decrease range.
Balance & Calibration:
If the Drive is unbalanced, vibrating, or not turning properly:
- Place the Drive on flat ground. Foot mats should be even.
- Ensure the charger is unplugged and the hoverboard is off.
- Press and hold the power button for 10-15 seconds. The hoverboard will turn on, and the battery indicator will light up.
- After the light flashes 5 times consecutively, release the power button.
- Turn the hoverboard off, then back on. Calibration is complete.
Safety Alerts:
If a system error or improper operation occurs, the device will alert the user:
- Running indicator light turns red, a beep sounds, and the hoverboard may stop suddenly.
- Common occurrences triggering alerts:
- Unsafe riding surfaces (uneven, too steep).
- Low battery voltage.
- Drive is still charging.
- Platform tilts due to excess speed during operation.
- Hoverboard overheating or high motor temperature.
- Drive rocking back and forth for over 30 seconds.
- System enters protection mode (alarm indicator lights up, hoverboard vibrates) when battery is low.
- Platform tilted forward or backward more than 10 degrees (Drive powers off, stops suddenly, causing loss of balance/fall).
- Tires blocked (Drive stops after 2 seconds).
- Battery level depleted below protection mode (Drive powers off after 15 seconds).
- High discharge current (e.g., driving up steep slope for long time) (Drive powers off after 15 seconds).
- Warning: If the Drive turns off during a safety alert, all operations halt. Do not attempt to ride. Turn off and back on to unlock from safety lock.
Charging Your Drive:
- Ensure no dust, debris, or dirt in the charging port.
- Plug the charger into a grounded wall outlet; the charger indicator light will be green.
- Connect the charging cable (100V-240V; 50Hz/60Hz) to the power supply.
- Align and connect the 3-pin charging cable to the Drive's charging port. DO NOT FORCE THE CHARGER, as this can break prongs or cause permanent damage.
- Once connected, the charger's indicator light will turn red, indicating charging.
- When the charger's red light turns green, the hoverboard is fully charged (up to 6 hours).
- If charging while powered on, a yellow flashing light on the hoverboard indicates charging.
- After full charge, unplug the charger from the Drive and the power outlet.
Battery Care / Maintenance:
- Battery Specifications:
- Battery Type: Rechargeable lithium-ion battery
- Charge Time: Up to 6 hours
- Voltage: 36V
- Initial Capacity: 2Ah
- Battery Maintenance:
- The lithium-ion battery is built into the Drive. Do not disassemble or attempt to remove it.
- Use only the supplied Hover-1 charger and cable. Other chargers may cause damage, overheating, or fire, and void the warranty.
- Do not connect the Drive or battery to a power supply plug or car cigarette lighter.
- Do not place the Drive near fire or in direct sunlight; heating can break or ignite the battery.
- Do not continue charging if the battery does not recharge within the specified time; it may cause the battery to become hot, rupture, or ignite.
- Recycle or dispose of batteries properly. Lithium-ion batteries are prohibited in ordinary trash. Consult local waste authority for information.
- Do not attempt to modify, change, or replace the battery.
- Warning: Failure to follow safety precautions can lead to serious bodily injury or death.
- Do not use if the battery emits odor, overheats, or leaks.
- Do not touch leaking materials or breathe fumes.
- Do not allow children or animals to touch the battery.
- The battery contains dangerous substances. Do not open or insert anything into the battery.
- Do not attempt to charge if the battery has discharged or emits substances. Immediately distance yourself in case of fire or explosion.
- Warning: Seek immediate medical assistance if exposed to any substance emitted from the battery.
Care & Maintenance:
- To avoid damage to internal circuitry, do not expose to liquid, moisture, or humidity.
- Do not use abrasive cleaning solvents.
- Do not expose to extremely high or low temperatures; this shortens electronic component life, destroys the battery, and/or distorts plastic parts.
- Do not dispose of in fire; it may explode or combust.
- Avoid contact with sharp objects to prevent scratches and damage.
- Do not allow the Drive to fall from high places; this can damage internal circuitry.
- Do not attempt to disassemble.
- Use only the charger provided by Hover-1.
- Warning: Avoid using water or other liquids for cleaning. If liquids enter, it will cause permanent damage to internal components.
- Warning: Disassembling the Drive without permission from Hover-1 voids the warranty.
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Instructions for a Class B Digital Device or Peripheral:
This equipment has been tested and complies with Class B digital device limits. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try to correct it by:
- Reorienting or relocating the receiving antenna.
- Increasing separation between equipment and receiver.
- Connecting equipment to an outlet on a different circuit.
- Consulting the dealer or an experienced radio/TV technician.
Warranty:
For warranty information, visit www.hover-1.com.
Manufacturer: DGL Group, Ltd., 2045 Lincoln Highway, Edison, NJ 08817.
TEL: 732-692-5000.
Affix Serial Number Label in the designated area.
Need help?
General
To Next Page
