What to do if Hoymiles Inverter shows firmware error?
Check if the firmware is correct and upgrade again. Also, check and ensure proper communication between the DTU, Hoymiles monitoring system, and the microinverter; retry if needed. If the fault still exists, contact your dealer or Hoymiles technical support.
What to do if my Hoymiles Inverter is offline?
First, ensure the microinverter is functioning correctly. Then, check the communication status between the DTU and the Hoymiles monitoring system, or between the DTU and the microinverter; try to improve the communication if it's poor. If the issue persists, contact your dealer or Hoymiles technical support.
What to do if Hoymiles Inverter shows grid overvoltage?
If the alarm occurs accidentally, it's possible the grid voltage is temporarily abnormal; the microinverter should recover automatically once the voltage returns to normal. However, if the alarm occurs frequently, verify that the grid voltage is within the acceptable range. If it's not, contact your local power operator or, with their consent, adjust the grid overvoltage protection limit via the Hoymiles monitoring system.
What to do if my Hoymiles Inverter shows '10 min value grid overvoltage'?
If this alarm appears once in a while, it might be due to a temporary issue with the grid voltage. The inverter should fix itself when the voltage goes back to normal. If it keeps happening, check if the grid voltage is within the right range. If it's not, get in touch with your local power company or, with their agreement, change the grid overvoltage protection limit using the Hoymiles monitoring system.
What to do if Hoymiles Inverter reports grid undervoltage?
If you see this alarm just once, it could be because the grid voltage is briefly not normal. The microinverter should automatically get back to normal when the grid voltage stabilizes. If it happens a lot, check to see if the grid voltage is in the right range. If it's not, contact your local power operator, or change the grid undervoltage protection limit through the Hoymiles monitoring system after getting permission from the local power operator.
What to do for over temperature protection in Hoymiles Inverter?
First, check the ventilation and ambient temperature where the microinverter is installed. If needed, improve ventilation and heat dissipation. If ventilation and temperature are within the correct range, contact your dealer or Hoymiles technical support.
What to do if Hoymiles Inverter displays grid configuration parameter error?
Check if the grid configuration parameter is correct and upgrade again. If the fault still exists, contact your dealer or Hoymiles technical support.
What to do if my Hoymiles Inverter shows software error code 126?
If the alarm occurs accidentally and the microinverter is still working properly, no special action is required. However, if the alarm occurs frequently and cannot be resolved, contact your dealer or Hoymiles technical support.
What to do if my Hoymiles Inverter shows software error code 128?
If the alarm occurs accidentally and the microinverter functions normally, no action is needed. If the alarm occurs frequently and cannot be recovered, contact your dealer or Hoymiles technical support.
What to do if my Hoymiles Inverter shows software error code 129?
If the alarm occurs accidentally and the microinverter can still work normally, no special treatment is required. If the alarm occurs frequently and cannot be recovered, contact your dealer or Hoymiles technical support.
Defines safety symbols used in the manual and their meanings.
Provides critical safety instructions for installation and operation of the microinverter.
Covers unpacking the microinverter and checking its contents.
Provides criteria for selecting the best installation location for the microinverter.
Guides on connecting the microinverters to the PV modules.
Lists checks to perform before energizing the system.
Guides on establishing an internet connection for remote monitoring.
Provides a list of common issues, alarm codes, and suggested solutions.
General| Total Harmonic Distortion (THD) | <3% |
|---|---|
| Cooling Method | Natural Convection |
| Weight | 4.5kg |
| Product Name | HMS-800W-2T |
| Peak Power Tracking Voltage Range | 16V-60V |
| Nominal Output Voltage/Range | 230V |
| Output Voltage | 230V |
| Nominal Output Frequency/Range | 50Hz/60Hz |
| Output Frequency | 50Hz/60Hz |
| Power Factor | >0.99 |
| Efficiency CEC | 96.5% |
| Protection Features | Over Temperature Protection |
To Next Page
