Hozelock 130 - Maintenance Procedures; Cleaning the Filter

•IftheTSSistofunctioncorrectlyallgun
releasing and depressing operations must be
performed at intervals over 4-5 seconds.
DO NOT PULSE THE TRIGGER.
•Topreventdamagetotheappliance,when
running do not stop the water jet for more
than 10 minutes at a time. If the product is
not used for more than 10 minutes please
ensure that the on/off switch is switched to off
(OFF/0) to prevent damage to the appliance.
Adjusting the spray nozzle
•Waterowisadjustedbyregulating
the nozzle. (fig.14)
Stopping the appliance
•SettheON/OFFswitchtooff(OFF/0).(g.15)
•Depresstheguntriggeranddischargethe
residual pressure inside the hoses.
•Engagethegun’sreadsafetybutton(X).
(fig.11)
Restarting
•Releasethegun’sredsafetybutton(X).(g.11)
•Ensurewaterisconnected
•Depresstheguntriggeranddischargethe
residual air inside the hose.
•Settheon/offswitchtoon(ON/1).(g.10)
Storage
•Switchtheapplianceoff(OFF/0).(g.15)
•Removetheplugfromthesocket.
•Turnoffthewatersupplytap.
•Dischargetheresidualpressurefromthegun
by pressing the trigger, until all the water has
come out of the nozzle.
•Drainthedetergenttank.
•Disconnectthehighpressurehosefromthe
gun by pressing the red quick release button
and remove the hose end (fig.21).
•Disconnectthehighpressurehosefromthe
pressure washer by pressing the red quick
release button at the back of the product and
remove the hose (fig.22).
•Returntheguntoitsstorageposition.
•Coilthehighpressurehosetakingcarenotto
kink it and store in its storage area at the side
of the product. (fig.24)
•Engagethegun’sredsafetybutton(X).
Filling and using detergent
•Removethedetergenttankfromit’sstorage
location (fig.16).
•Removethenozzlebytwistingandpulling
upwards (fig.17).
•Fillthetankwithhighlydegradabledetergent
mixed with water as recommended on the
detergent’sdirections(g18)andretthe
nozzle.
•Attachthedetergenttanktothelance
extension (J) by pushing in and twisting until it
stops (figs.19 & 20).
Using detergent feature
•Maximumcleaningisachievedbyapplying
the detergent mixed with water to the surface
while still dry. When dealing with vertical
surfaces work from the bottom upwards.
Leave the detergent to act for 1-2 minutes
but do not allow the surface to dry. Starting
from the bottom, use the high pressure jet at
a minimum distance of 30cm. Do not allow the
rinse water to run onto unwashed surfaces.
Maintenance
Any maintenance operations not covered by
this chapter should be carried out by a qualified
engineer.
CAUTION - DANGER! Always disconnect the
plug from the power socket before carrying
out any work on the appliance.
Cleaning the nozzle
•Disconnectthelancefromthenozzle.
•Removeanydirtdepositsfromthenozzlehole
using the tool (M). As shown in (fig.25)
Cleaning the filter
•Cleanthesuctionlterafterevery5hoursof
operation or as required, as shown in
(figs.26 & 27). The cleaning interval required
will vary on the hardness of your water so you
should inspect the filter regularly
End-of-season storage
•Ensurethereisnoresidualwaterleftinthe
appliance and protect against frost.