EasyManuals Logo

HP Enterprise HPE 5820 Switch Series User Manual

HP Enterprise HPE 5820 Switch Series
46 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #35 background imageLoading...
Page #35 background image
31
<DeviceB> system-view
[DeviceB] irf member 1 renumber 2
Warning: Renumbering the switch number may result in configuration change or loss.
Continue? [Y/N]:y
[DeviceB]
2. Power off the devices, connect IRF links as shown in Figure 13, and power on the two devices.
3. Configure IRF port bindings:
# Bind Ten-GigabitEthernet 1/0/25 to IRF-port 1/2 on Device A and save the configuration.
<DeviceA> system-view
[DeviceA] interface ten-gigabitethernet 1/0/25
[DeviceA-Ten-GigabitEthernet1/0/25] shutdown
[DeviceA-Ten-GigabitEthernet1/0/25] quit
[DeviceA] irf-port 1/2
[DeviceA-irf-port1/2] port group interface ten-gigabitethernet 1/0/25
[DeviceA-irf-port1/2] quit
[DeviceA] interface ten-gigabitethernet 1/0/25
[DeviceA-Ten-GigabitEthernet1/0/25] undo shutdown
[DeviceA-Ten-GigabitEthernet1/0/25] save
# Bind Ten-GigabitEthernet 2/0/26 to IRF-port 2/1 on Device B and save the configuration.
<DeviceB> system-view
[DeviceB] interface ten-gigabitethernet 2/0/26
[DeviceB-Ten-GigabitEthernet2/0/26] shutdown
[DeviceB-Ten-GigabitEthernet2/0/26] quit
[DeviceB] irf-port 2/1
[DeviceB-irf-port2/1] port group interface ten-gigabitethernet 2/0/26
[DeviceB-irf-port2/1] quit
[DeviceB] interface ten-gigabitethernet 2/0/26
[DeviceB-Ten-GigabitEthernet2/0/26] undo shutdown
[DeviceB-Ten-GigabitEthernet2/0/26] save
# Activate IRF port configuration on Device A.
[DeviceA-Ten-GigabitEthernet1/0/25] quit
[DeviceA] irf-port-configuration active
# Activate IRF port configuration on Device B.
[DeviceB-Ten-GigabitEthernet2/0/26] quit
[DeviceB] irf-port-configuration active
After the IRF port configuration is activated, the two devices automatically elect a master. In this
example, Device A is the master. Device B automatically reboots and joins the Device A as a
subordinate to form an IRF fabric. The system name of the IRF fabric is DevcieA.
4. Configure LACP MAD:
# Create a dynamic aggregate interface and enable LACP MAD. Because LACP MAD is not run
between IRF domains, you can use the default value 0.
<DeviceA> system-view
[DeviceA] interface bridge-aggregation 2
[DeviceA-Bridge-Aggregation2] link-aggregation mode dynamic
[DeviceA-Bridge-Aggregation2] mad enable
You need to assign a domain ID (range: 0-4294967295)
[Current domain is: 0]:
The assigned domain ID is: 0

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Enterprise HPE 5820 Switch Series and is the answer not in the manual?

HP Enterprise HPE 5820 Switch Series Specifications

General IconGeneral
BrandHP Enterprise
ModelHPE 5820 Switch Series
CategorySwitch
LanguageEnglish

Related product manuals