HP 3458A - Page 14

T .O . 33 K8-4-551-1

Table 1 . (Cont .)
Test Instrument (TI)
Characteristics
Performance

Test
Specifications

Method
AC Current

Range : 0 to 1 AAC
Accuracy:
Relative: ±(% of rdg + % of mg)
Absolute : ±[Sgrt(TI % of rdg^2 +
STD 1 % of rdg^2 + STD2 % of rdg^2 +
STD3 % of rdg A 2) + TI % of rng]
Implicitly calibrated
during DC Current and
AC Voltage Calibration
Range

Frequency
100 µA 10 to 20 Hz
20 to 40 Hz
40 to 45 Hz
45 to 100 Hz
100 Hz to 1 kHz
1 mAto

10to20Hz
100 mA

20 to 40 Hz
40 to 45 Hz
45 to 100 Hz
100 Hz to 5 kHz
5 to 20 kHz *
20 to 50 kHz *
1
50 to 100 kHz *
1 A

10 to 20 Hz
20 to 40 Hz
40 to 45 Hz
45 to 100 Hz
100 Hz to 5 kHz
5to20kHz * I
20 to 50 kHz *
Relative

Absolute
0.4 + 0 .03

(0 .4 + 0 .02 + 0 .0005277 + 0 .0005) + 0 .03
0 .15 + 0 .03

(0 .15 + 0 .0066 + 0 .0005277 + 0 .0005) + 0 .03
0 .15 + 0 .03

(0 .15 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .06 + 0 .03

(0 .06 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .06 + 0 .03

(0 .06 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .4 + 0 .03

(0 .4 + 0 .02 + 0 .0005277 + 0 .0005) + 0 .03
0 .15 + 0 .03

(0 .15 + 0 .0066 + 0 .0005277 + 0 .0005) + 0 .03
0 .15 + 0 .03

(0
.15 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .06 + 0 .03

(0 .06 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .06 + 0 .03

(0 .06 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .03
0 .06 + 0 .02

(0 .06 + 0 .0024 + 0 .0005277 + 0 .0005) + 0 .02
0 .4 + 0 .04

(0.4 + 0 .0046 + 0 .0005277 + 0 .0005) + 0 .04
0 .55 + 0 .15

(0 .55 + 0
.0071 + 0 .0005277 + 0 .0005) + 0 .15
0 .4 + 0 .02

(0.4 + 0 .02 + 0
.0005277 + 0 .0006) + 0 .02
0 .16 + 0 .02

(0 .16 + 0 .0066 + 0 .0005277 + 0 .0006) + 0
.02
0 .16 + 0 .02

(0 .16 + 0 .0024 + 0 .0005277 + 0 .0006) + 0 .02
0 .08 + 0 .02

(0 .08 + 0 .0024 + 0 .0005277 + 0 .0006) + 0 .02
0 .1 + 0 .02

(0.1 + 0 .0024 + 0.0005277 + 0 .0006) + 0 .02
0 .3 + 0 .02

(0 .3 + 0 .0024 + 0 .0005277 + 0 .0006) + 0 .02
1 + 0 .04

(1 + 0 .0046 + 0 .0005277 + 0 .0006) + 0 .04
* 1
*2
* 3
Typical accuracies, will not be calibrated.
Calibration of the complete Voltage and/or Frequency ranges at these points are not possible due to the
capability limitations of the Calibration Standards . The TI does not require a limited certification for these
Standards limitations.
Option HO1 1000 V rms max (All other units 700 V rms max).
12