HP 54520 Series - Page 282

Index
# (number) of points softkey, 4-25, 10-12 Chan/Mem (channel/memory) softkey,
# (number) of screens softkey, 6-5
# (number) of segments softkey, 4-25
(+) Plus function, 10-5
(-) Minus function, 10-5
(x) Times function, 10-5
+ width, 13-18
- width, 13-18
4-bit pattern, 5-10
A
Abort softkey, 11-12
AC BNC softkey, 11-18
Address softkey, 11-7
adjust mode, 5-6
Adjust softkey, 4-29, 5-21
After fail softkey, 8-13, 8-19
air flow, 1~7
aliasing, 10-18
Allowance softkey, 8-17
altitude characteristics, 14-23
Attenuation menu, 11-11
attenuation too high or bad connection
error message, 1]-11
auto mode, 5-4
Auto softkey, 4~29
auto triggered, 5-2
Autoincrement softkey, 12-18
autoscale, 2-4
undo, 2-5
average mode, 6-5
averaging, 4-16
B
bandwidth limit characteristics, 14-8
bandwidth specifications, 14-3
baud rate, 11-4
binary file format, 12-6
bitmapped file, 12-14
blue shift. key, 2-15 to 2-16
Cc
Cal (calibration) signal characteristics,
14-21
Cancel key, 2-10
Center freq (frequency) softkey, 10-11 to
10-12
center mode, 5-6
Center softkey, 5-21
10-4, 10-6
channel
indicator, 3-2
models, 3-2
selection, 3-4
timing adjustments, 11-13
Channel factors softkey, 2-18, 11-17
Channcl impedance softkey, 11-12
Channel labels softkey, 2-18, 11-17
Channel softkey, 3-4, 11-11, 11-13
characteristics
automatic pulse parameter
measurements, 14-19
bandwidth limit, 14-8
Cal (calibration) signal, 14-21
disk drive, 14-20
display, 14-13
display modes, 14-14
enviornmental conditions, 14-23
FFT (fast Fourier transform), 14-7,
14-16
general, 14-23 to 14-25
hardcopy, 14-20
horizontal, 14-6, 14-10
HP-IB Programmability, 14-20
marker, 14-15
operating, 14-8 to 14-22
performance, 14-5 to 14-7
sctup aids, 14-20
trigger, 14-6, 14-10
vertical, 14-5, 14-8 to 14-9
waveform math, 14-15
waveform save, 14-18
window, 14-17
Clear display key, 2-7
Clear key, 2-15
Clicker softkey, 11-17
clipped signal, 13-17
Clock softkey, 5-13
Compare softkey, 8-17
Compression softkey, 12-17
Connect dots softkey, 6-6
connect the dots, 10-15, 14-14
Continue softkey, 8-19, 11-11
Continuous softkey, 8-5 to 8-6
control area, 2-4
coupling, 5-7
Coupling softkey, 3-6
cursor setting, 14-16
D
A time, 8-9, 13-15
data
calculating, 2-7
collection, 13-4
destination, 8-12
display, 2-7
failure, 8-12
in memory, 4-30
record calculating, 13-6
saving failure, 8-18
storage, 8-10
transfer rate, 14-21
Data source softkey, 8-8
Date softkey, 11-16
dBm computation, 10-17
dBV computation, 10-18
de value, 10-18
default resetting, 2-12
Define measure softkey menu, 8-2
Define measurement menu, 8-7
delay
reference point, 4-11
trigger mode, 5-15
Delay softkey, 4~5, 5-17
Delete key, 12-19
delta entry calculations, 7-3
delta-t accuracy specifications, 14-4
demensions characteristics, 14-24
device communications, 11-4
Diff (differentiate) function, 10-6
dimensions instrument, 14-24
Disabled/Enabled softkey, 12-16
disk
formatting, 12-20
operation, 12-12, 12-15, 12-17
storing, 12-13, 12-16
disk drive
characteristics, 14-20
overview, 2-20
Disk menu, 12-2 to 12-3
Index-1