HP 54520 Series - Page 285

Index
operating conditions
Sce general characteristics
Operator softkey, 10-4
Or if softkey, 8-11
oscilloscope operation, 4-23
overshoot
defined, 13-13
measurement, 13-18
overwriting, 6-8
P
panning, 4-6
Paper length softkey, 11-8
pass (screen message), 8-16
Pattern softkey, 5-10
pattern trigger mode, 5-9, 5-13
PCX files, 12-16
peak
detect mode, 6-8
frequency accuracy, 10-16
measurement, accuracy, 10-15
Peak search softkey, 10-10
Pen softkey, 11-9
Percent/Volts softkey, 8-8
performance characteristics, 14-5 to 14-7
persistence made, 6-4
pixel
file, 12-14
memory, 8-13, 8-19
memory file, 12-5
Plot softkey, 11-9
plotting, 11-9
See also printing
points setting, 14-16
position knob, 3-2
positive delay, 4-5
positive time, 5-3
power
cord, 1-5
requirements, 1-5, 14-24
Present softkey, 5-14
preshoot.
defined, 13-13
measurement, 13-18
Print key, 2-10
printing, 2-10, 11-19
to printer, 11-8
probe
attenuation, 3-8
calibration, 11-11 to 11-12
compensation, 2-17, 14-21
compensation signal, 11-18
impedance, 11-12
terminals, 2-17
Run key, 2-6, 4-25
running (screen display), 4-4
Ss
Sample clock softkey, 4-29
sampler circuit, 5-3
sampling rate, 4-29
probe attenuation (screen message), 11-11] Save key, 2-12
Probe cal (calibration) menu, 11-10
Probe softkey, 3-8
product
requlations, 14-25
support, 14-22
Protect on: cannot store to memory
(screen message), 8-18
pulse width measurements, 13-18
Q
Qualify on softkey, 5-16
R
Real time acquisition display menu, 6-7,
6-9 to 6-14
real time mode, 4-17, 13-16
Real-time clock, 11-15
rear panel, 1-4 to 1-7
Recall Clr (clear), 2-20
Recall key, 2-12
record length, 4-29 to 4-30
Record length softkey, 4-30
rectangular window, 10-14
Reference softkey, 4-11
Registration form (print) softkey, 11-19
regulations for product, 14-25
Reject softkey, 5-7
Reject-Coupling softkey, 5-7
Rendering softkey, 12-17
Repetitive acquisition display menu, 6-3
repetitive mode, 4-12, 13-16
Repetitive/Real time softkey, 4-12
reset instrument, 2-20
rise time
measurement, 13-18
specifications, 14-3
rising edge
caleulations, 13-9 to 13-11
defined, 13-11
saving
data failure, 8-18
hardcopy, 8-13, 8-19
pixel memory, 8-19
screen display
nsec, 4-4
running, 4-4
Screen softkey, 8-5
Search level softkey, 10-10
segment, 4-25
Segment # (number) softkey, 6-11
Self-Cal (calibration) menu, 11-14
Self-test menu, 11-10
Sensitivity softkey, 10-6, 10-13
sequencing, 2-16
sequential
memory, 4-24
single shot, 4-23
Sequential softkey, 4-23 to 4-28
Service menu, 11-14
Set softkey, 8-11
setup
aids, 14-20
file, 12-5, 12-14
shipping, 1-3
Show key, 2-11
signal
analyzing, 2-4
clipped, 13-17
locating, 2-4
noise, 6-5
optomizing, 2~4
repetitive, 2-4
single persistence, 6-8
single shot
acquisition, 4-17, 14-21
events, 2-8
sequential, 4-23 to 4-28
Slope softkey, 5-7
Index-4