HP 54520 Series - Page 286

index
softkey
# (number) of points, 4-25, 10-12
# (number) of sercens, 6-5
# (number) of segments, 4-25
Abort, 11-12
AC BNC, 11-18
Address, 11-7
Adjust, 4-29, 5-21
After fail, 8-13, 8-19
Allowance, 8-17
Auto, 4-29
Autoincrement, 12-18
Center, 5-21
Center freq (frequency),10-1] to 10-12
Char/Mem (channel/memory),10-4, 10-6
Channel, 3-4, 11-11, 11-13
Channel factors, 2-18, 11-17
Channel impedance, 11-12
Channel labels, 2-18, 11~17
Clicker, 11-17
Clock, 5-13
Compare, 8-17
Compression, 12-17
Connect Dots, 6-6
continue, 8-19, 11-11
Continuous, 8-5 to 8-6
Coupling, 3-6
Data source, 8-8
Date, 11-16
Delay, 4-5, 5-17
Display, 6-3, 6-10, 10-4
ECL (Emmitter Couple Logic}, 3-9
Enabled/Disabled, 12-16
inter changes, 6-13
Exclude, 6-12
Exclude all changes, 6-13
Exclude include, 6-12
Execute, 12-15
Exit menu, 11-13, 11-19
Extended analysis, 8-6
Fail if, 8-12
Field, 5-20
File format, 12-6
Form feed, 11-8
Format, 12-16
Freq (frequency) span, 10-11
From, 12-14
From file, 12-12
softkey (continued)
From seg (segment) # (number), 6-12
Function, 10-4
Ground markers, 2-18, 11-17
Holdoff, 5-8, 5-11, 5-14, 5-20, 5-22
Horiz (horizontal) magnify, 10-11
HP-IB/RS-232, 11-4
Inchide, 6-12
Initialize, 11-8
Input impedance, 3-7
Interpolation, 11-19
Level, 5-6, 5-20 to 5-21
Line, 5-20
Lower threshold, 8-9
Markers, 8-6
Max (maximum) test voltage, 11-12
Measure window, 8-5
Measurements, 8-9
Mode, 5-4
More, 3-9, 6-13, 10-11, 10-14
More exclude include, 6-12
More preset probe, 3-7
Number (#) of points, 4-25
Number (#) of screens, 6-5
Number (#) of segments, 4-25
Off on, 7-3
Off/Frame/Axes/Grid, 6-6
Offset, 3-5, 10-6, 10-14
On fail save, 8-12 to 8-13
On fail, save, 8-18
Operator, 10-4
Or if, 8-11
Paper length, 11-8
Pattern, 5-10
Peak search, 10-10
Pen, 11-9
Percent/Voits, 8-8
Plot, 11-9
Present, 5-14
Probe, 3-8
Qualify on, 5-16
Record length, 4-30
Reference, 4-11
Registration form (print), 11-19
Reject, 5-7
Reject-Coupling, 5-7
Rendering, 12-17
RepetitiveReal time, 4-12
softkey (continued)
resct, 2-20
Sample clock, 4-29
Sercen, 8-5
Search level, 10-10
Sensitivity, 10-6, 10-13
Sequential, 4-23 to 4-28
Set, 8-11
Slope, 5-7
Source, 5-6, 6-11
Source xl, yl, 7-3
Source x2, y2, 7-5
Standard/User defined, 8-8
Stardard/Source, 5-19
Start cal (calibration), 11-11
Statistic output, 8-6
Statistics, 8-5
Stop, 8-19
System util, 11-17
Test, 8-11, 8-15
Thresholds/Measurements, 8-8
Time, 11-13, 11-16
Time base menu, 4-3
Time out, 11-7
Time/Div (division), 4-4
To, 8-17, 12-12
To file, 12-15, 12-17
To seg (segment) # (number), 6-13
Trig’d (triggered) auto, 5-4
Trigger on, 5-17
Trigger, common ones, 5-4
TTL (Transistor Transistor Logic), 3-9
Type, 12-5, 12-14
unlabeled, 5-10, 5-19
Upper threshold, 8-9
Vertical sensitivity, 3-4
When, 5-11, 5-13
When present, 5-22
Width, 5-22
Window, 10-14
x1 Position, 7-4
x2 Position, 7-5
yl Position, 74
y2 Position, 7-5
Source softkey, 5-6, 6-11
Source x1, yl softkey, 7-3
Source x2, y2 softkey, 7-5
Index-5