EasyManuals Logo

HP LE1901w User Manual

HP LE1901w
45 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
Maintenance Guidelines
To enhance the performance and extend the life of the monitor:
Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those
controls that are covered in the operating instructions. If the monitor is not operating properly or
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
Use only a power source and connection appropriate for this monitor, as indicated on the label/
back plate of the monitor.
Be sure the total ampere rating of the products connected to the outlet does not exceed the current
rating of the electrical outlet, and the total ampere rating of the products connected to the cord does
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS
or A) for each device.
Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the
plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
Turn the monitor off when not in use. You can substantially increase the life expectancy of the
monitor by using a screen saver program and turning off the monitor when not in use.
NOTE: Monitors with a “burned-in image” are not covered under the HP warranty.
Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked
or covered. Never push objects of any kind into cabinet slots or other openings.
Do not drop the monitor or place it on an unstable surface.
Do not allow anything to rest on the power cord. Do not walk on the cord.
Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.
When removing the monitor base, you must lay the monitor face down on a soft area to prevent it
from getting scratched, defaced, or broken.
Cleaning the Monitor
1. Turn off the monitor and the computer.
2. Unplug the monitor from the wall outlet.
3. Clean the monitor plastics with a clean cloth dampened with water.
4. Clean the monitor screen with an antistatic screen cleaner.
CAUTION: Do not use benzene, thinner, ammonia, or any other volatile substances to clean the
monitor or the screen. These chemicals may damage the cabinet finish as well as the screen.
Shipping the Monitor
Keep the original packing box in a storage area. You may need it later if you move or ship the monitor.
4 Chapter 2 Safety and Maintenance Guidelines ENWW

Table of Contents

Other manuals for HP LE1901w

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP LE1901w and is the answer not in the manual?

HP LE1901w Specifications

General IconGeneral
3DNo
Pixel pitch0.2835 x 0.2835 mm
Display diagonal19 \
Display resolution1440 x 900 pixels
Vertical scan range56 - 76 Hz
Horizontal scan range24 - 83 kHz
Contrast ratio (dynamic)-
Contrast ratio (typical)1000:1
Viewing angle, horizontal160 °
Display brightness (typical)250 cd/m²
Supported graphics resolutions832 x 624, 1152 x 870, 1280 x 960, 1024 x 768 (XGA), 1280 x 1024 (SXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Operating temperature (T-T)5 - 35 °C
CertificationCE, FCC, CUL, CCIB, CCEE, IT ECO
Product colorBlack
Country of originChina
Plug and PlayYes
LED indicatorsPower
Tilt angle range-5 - 25 °
Cable lock slot typeKensington
Panel mounting interface100 x 100 mm
DVI-D ports quantity0
Power consumption (standby)2 W
Power consumption (typical)29 W
Sustainability certificatesENERGY STAR
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth (without stand)59 mm
Width (without stand)446 mm
Height (without stand)301 mm
Weight (without stand)4300 g

Related product manuals