Index
Compaq ProLiant DL360 Server Maintenance and Service Guide Index-5
COMPAQ CONFIDENTIAL Codename: MicroMachines Part Number: 169616-006 Last Saved On: 12/21/01 9:08 AM
firmware needs upgrading 4-42
is not configured 4-43
located in special graphics slot 4-43
reported POST error 4-43
restarted with a signature of zero 4-43
CPU Fan (Fan X) failure detected 4-13
CPU Fan controller not responding 4-14
Current SCSI bus cable configuration is not
recommended 4-14
DC-DC Converter Failed 4-11
Disable command issued 4-43
Disk 0 Configuration Error 4-25
Disk 0 Failure 4-21
Disk 1 Error 4-25
Disk 1 Failure 4-21
Disk Controller Failure 4-21
Diskette Controller Error 4-13
Diskette Drive Type Error 4-13
drive (bay) X
firmware needs upgrading 4-43
has insufficient capacity for its
configuration 4-43
has invalid M&P stamp 4-43
has loose cable 4-43
is a replacement drive 4-44
is a replacement drive marked OK 4-44
is failed 4-44
is undergoing drive recovery 4-44
needs replacing 4-44
upload code not readable 4-44
was inadvertently replaced 4-44
drive array
Array Accelerator Battery Charge Low 4-26
Array Accelerator Battery Depleted 4-26
Array Accelerator Configuration Error 4-26
Array Accelerator Not Responding 4-26
Array Accelerator Read Error 4-27
Array Accelerator Write Error 4-27
Controller detects replacement drives 4-21
Drive Failure 4-21
Drive(s) Disabled due to Array Accelerator
Data Loss 4-27
External Drive Subsystem Error 4-20
not Configured 4-22
Operating in Interim Recovery Mode 4-23
Recovery Needed 4-23
Reports Valid Data 4-25
resuming Automatic Data Recovery
process 4-21
Drive Monitoring features are
unobtainable 4-44
Drive Monitoring is NOT enabled 4-44
Drive Not Responding 4-25
Drive time-out occurred on physical drive bay
X 4-44
Drive X indicates position Y 4-44
Duplicate write memory error 4-45
Error occurred reading RIS copy from SCSI
Port X 4-45
Fan controller not responding 4-14
Fan failure detected 4-13
Fatal ROM Error 4-9
Fixed Disk 0 does not support DMA
Mode 4-16
Fixed Disk does not support Block Mode 4-17
Fixed Disk failed Identify command 4-17
Fixed Disk failed Set Block Mode
command 4-17
FYI, Drive (bay) X is non-Compaq
supplied 4-45
I/O Fan (Fan X) failure detected 4-13
I/O Fan controller not responding 4-14
I/O ROM Error 4-9
Identify controller data did not match
NVRAM 4-45
Identify logical drive data did not match
NVRAM 4-45
Incorrect Drive Replaced 4-24
Insufficient adapter resources 4-45
Internal SCSI Jumper Board Not Installed 4-14
Invalid Memory Configuration 4-10
Invalid Memory Speed 4-10
Keyboard Controller Error 4-12
Keyboard Error 4-12
Keyboard or System Unit Error 4-12
Less than 75% batteries at sufficient
voltage 4-45
Locked SCSI Bus Detected. 4-14
Log Reinitialized 4-10
Logical drive X failed due to cache error 4-46
Logical drive X status
Failed 4-46
Interim Recovery 4-46
Loose Cable Detected 4-46
Needs Recover 4-46
Overheated 4-46
Overheating 4-46
Recovering 4-46
Wrong Drive Replaced 4-47
Loose cable detected, logical drives may be
marked FAILED 4-47
Low System Battery 4-14
Memory Address Error 4-10
Memory Detection Failure 4-10
Memory Error 4-10
Mirror data miscompared 4-47
No configuration for accelerator board 4-47
Nonfunctioning Voltage Regulator
Module 4-11
NVRAM configuration present, controller not
detected 4-47
To Next Page
Loading...
