What to do if HP Storage attention LED is lit after cartridge load?
If the Attention LED is lit, but the Cleaning LED is not lit after loading a cartridge, it indicates that the Library was unable to complete the requested operation with the selected tape cartridge.
What to do if my HP Storage shows no display messages?
If your HP Storage shows no display messages, take the following actions: 1. Check that the power cord is properly connected. 2. Ensure the power button on the front panel is pressed and the green READY LED is lit. 3. Try power cycling the device. 4. If the display remains blank but the device appears powered on, attempt to retrieve the device status or error information from the RMI.
How to troubleshoot yellow power supply LED on HP MSL4048, MSL8048, and MSL8096 Storage?
A yellow LED on the power supply indicates that the power supply fan is not rotating at an acceptable speed. To resolve this: 1. Check the power supply fan for any obstructions. 2. If there are no obstructions, replace the power supply.
What does “!” mean in HP STORAGEWORKS MSL4048 operator panel inventory display?
The “!” symbol next to a data cartridge in the inventory indicates that the cartridge is either damaged, incompatible with the drive, or the wrong type for the attempted operation. The suggested solution is to export the data cartridge.
How to remove tape stuck in HP Storage drive?
To remove a tape stuck in the drive, the tape drive must rewind the tape before ejecting it. This process can take up to five minutes, depending on how much tape needs to be rewound. The READY light will flash during rewinding. Wait for the rewinding to complete before attempting any other operation.
Why my HP STORAGEWORKS MSL4048 Storage cannot load the cleaning cartridge?
If you cannot load the cleaning cartridge: * Make sure you are using an Ultrium Universal cleaning cartridge. * Ensure the cleaning cartridge has not expired. Cleaning cartridges expire after 50 cleaning cycles.
What to do if a cartridge recently imported from a different environment is causing issues with my HP Storage?
If a cartridge recently imported from a different environment is causing issues, allow the cartridge to acclimate for at least 24 hours before use. This is especially important if it was stored at a significantly different temperature or humidity level than the device.
How to troubleshoot a particular cartridge setting off the Attention LED and possibly the Cleaning LED on HP STORAGEWORKS MSL4048 Storage?
If the Media Attention LED clears after cleaning the drive, but immediately reappears each time a specific cartridge is reloaded, suspect that the cartridge is defective.
What causes HP Storage to fail writing to or reading from tape?
If you cannot write to or read from a tape, ensure that the cartridge is not a WORM cartridge that has already been used.
How to troubleshoot HP Storage tape stuck in storage slot?
To remove a tape stuck in a storage slot, follow these steps if the operator control panel or the remote management interface is operational: 1. Use the Move Tape command to move the tapes from the drives to the magazines. 2. Use the magazine removal process to release the magazine and remove it from the device.
Discusses available features like redundant power, encryption kits, and library extenders.
Details SCSI interface types, host bus adapters, and LUN support for SCSI drives.
Details FC interface types, speeds, and HBA recommendations for FC drives.
Specifies SAS interface requirements, speeds, and cable recommendations.
Explains how to configure tape drives into independent logical libraries for different backup policies.
Description and illustration of the tape library's front panel components.
Description and illustration of the tape library's back panel connectors and ports.
Steps to prepare the host computer and system for tape library installation.
Guidelines for planning parallel SCSI bus setup, including bus configuration and throughput.
Key steps for planning SAS configuration, including HBA and cable requirements.
Information on connecting the library via Fibre Channel directly or through a SAN.
Criteria for selecting an appropriate installation location for the tape library.
Procedures for installing the tape library into a rack using provided rails.
Steps for installing new tape drives into available drive bays.
Steps to power on the tape library and verify initial status.
Initial configuration steps for the tape library, including password and network settings.
Procedures to verify the connection between the host computer and the tape library.
Information on compatible Ultrium data and cleaning tape cartridges and their part numbers.
Guidelines for proper handling, use, and maintenance of tape cartridges to ensure longevity.
Procedures and recommendations for labeling tape cartridges for quick identification and inventory.
Overview of the web-based interface for monitoring and controlling the library.
Displays current device and drive status, including power supply information.
Accessing static device information such as serial numbers, firmware, and ports.
Overview of configuration options for logical libraries, drives, network, and system settings.
Accessing functions like unlocking magazines, cleaning drives, and moving media.
Accessing diagnostic tests, firmware updates, viewing logs, and downloading support tickets.
Overview of the operator control panel functions for these specific models.
Steps to diagnose and resolve issues when parallel SCSI devices are not detected.
Solutions for issues related to Fibre Channel connections and link status.
Analysis of factors affecting performance, such as file size, file system, and connections.
Information on how to find and interpret error codes displayed on the OCP, RMI, or L&TT.
Lists the tools required for servicing the tape library.
Step-by-step guide for adding a new HP Ultrium tape drive.
Procedures for safely removing and installing tape drives.
Instructions for removing and replacing tape library magazines.
Guide for installing an optional redundant power supply.
Instructions for replacing the library controller module.
Steps for removing and replacing the base chassis assembly.
Information on how to contact HP technical support and what information to provide.
List of relevant HP websites for product information and support.
Information on HP's customer self-repair program for replacing parts.
Dimensions and weight details for MSL2024, MSL4048, MSL8048, and MSL8096 models.
Operating and non-operating environmental requirements for the tape library.
FCC rules and regulations regarding RF emission limits and device classification.
Safety and compliance information regarding the Class 1 laser product.
Safety and handling instructions for battery replacement.
Precautions to prevent damage from static electricity when handling components.
Various methods for proper grounding when working with electrostatic-sensitive parts.
General| Number of Slots | 48 |
|---|---|
| Drive Technology | LTO Ultrium |
| Number of Drives | Up to 4 |
| Product Type | Tape Library |
| Operating Humidity | 20% to 80% non-condensing |
| Operating Temperature | 10°C to 35°C |
| Form Factor | Rack-mountable |
To Next Page
