To Next PageTo Next PageHow to fix HP StorageWorks MSL8096 device not powering on?
If your HP Storage device isn't powering on, try these steps: 1. Ensure all power cord connections are secure. 2. Verify the power button on the front panel is pressed and the green READY LED is illuminated. 3. Confirm the outlet has power by testing with another working device. 4. If necessary, replace the power cord.
What to do if my HP StorageWorks MSL8096 Storage shows no display messages?
If your HP Storage shows no display messages, take the following actions: 1. Check that the power cord is properly connected. 2. Ensure the power button on the front panel is pressed and the green READY LED is lit. 3. Try power cycling the device. 4. If the display remains blank but the device appears powered on, attempt to retrieve the device status or error information from the RMI.
How to troubleshoot yellow power supply LED on HP MSL4048, MSL8048, and MSL8096 Storage?
A yellow LED on the power supply indicates that the power supply fan is not rotating at an acceptable speed. To resolve this: 1. Check the power supply fan for any obstructions. 2. If there are no obstructions, replace the power supply.
What does “!” mean in HP Storage operator panel inventory display?
The “!” symbol next to a data cartridge in the inventory indicates that the cartridge is either damaged, incompatible with the drive, or the wrong type for the attempted operation. The suggested solution is to export the data cartridge.
How to remove tape stuck in HP StorageWorks MSL8096 drive?
To remove a tape stuck in the drive, the tape drive must rewind the tape before ejecting it. This process can take up to five minutes, depending on how much tape needs to be rewound. The READY light will flash during rewinding. Wait for the rewinding to complete before attempting any other operation.
How to troubleshoot blue and green power supply LED status on HP MSL4048, MSL8048, and MSL8096 Storage?
The blue LED indicates that the power supply is connected to a functioning outlet, while the green LED should indicate that the power supply is producing adequate power. If the blue LED is lit but the green LED is off, replace the power supply.
How to resolve HP StorageWorks MSL8096 Storage LCD error code?
If the LCD displays an error code, look up the specific error code, attempt to resolve the underlying issue, and then power cycle the device.
What to do if HP StorageWorks MSL8096 Storage cannot connect to the remote management interface (RMI)?
If you cannot connect to the remote management interface (RMI), verify the following: * The device is connected to the LAN with a CAT 5E, 6, or 6E Ethernet cable. * The link LED on the RJ45 (LAN) connector is lit when the device is powered up. If the LED is not lit, the device is not communicating with the LAN.
How to fix HP Storage cleaning or data cartridge incompatibility?
To resolve cartridge incompatibility, ensure that you are using data and cleaning cartridges that are compatible with the drive and model of your device, and that you are using the correct cartridge type for the intended operation.
How to troubleshoot HP StorageWorks MSL8096 Storage tape stuck in storage slot?
To remove a tape stuck in a storage slot, follow these steps if the operator control panel or the remote management interface is operational: 1. Use the Move Tape command to move the tapes from the drives to the magazines. 2. Use the magazine removal process to release the magazine and remove it from the device.
General| Product Type | Tape Library |
|---|---|
| Number of Cartridge Slots | 96 |
| Number of Drives | 8 |
| Form Factor | Rackmount |
| Drive Type | LTO |
| Interface | SAS |
| Storage Capacity | Up to 288 TB (native) |
| Maximum Native Capacity (LTO-5) | 192 TB |
| Encryption | Yes |
| Dimensions (H x W x D) | 84.6 x 48.3 x 93.7 cm |
| Weight | 88 lb (40 kg) empty, 150 lb (68 kg) fully loaded |
