What causes SCI communication error in hpmont HD09-4T2P2G?
SCI communication errors in your hpmont Inverter can arise from a connection fault in the communication cable, a disconnected or poorly connected cable, a communication setting error, or communication data errors. To troubleshoot: * Check the connection of the communication cable. * Verify the communication format (F17.00) and baud rate (F17.01).
What to do if hpmont Inverter parameters auto-tuning fault?
If your hpmont Inverter's parameter auto-tuning fails, it is likely due to the parameter auto-tuning timing out. To address this: * Check the motor’s connection. * Input the correct motor parameters using settings F08.01 - F08.03.
What to do if hpmont Inverter shows fault of output phase?
If your hpmont Inverter reports a fault in the output phase, it may be due to output phase disconnection or loss, or a heavy imbalance of the inverter’s three-phase load. To resolve this: * Check the connection between the inverter and the motor. * Check the quality of the motor.
What causes DC bus undervoltage in hpmont HD09-4T2P2G Inverter?
DC bus undervoltage in your hpmont Inverter can occur at the beginning of powering on and the end of powering off, if the input voltage is too low, or if improper wiring leads to hardware undervoltage. Here’s how to troubleshoot: * Note that it is normal status of powering on and powering off. * Check the input power voltage. * Check the wiring and wire the inverter properly.
Why does hpmont Inverter heatsink overheat?
An hpmont Inverter's heatsink can overheat if the ambient temperature is too high, the inverter's external ventilation is poor, there's a fan fault, or there's a fault in the temperature detection circuit. Here’s how to address it: * Consider using an inverter with higher power capacity. * Improve the ventilation around the inverter. * Replace the cooling fan.
What to do if hpmont HD09-4T2P2G Inverter shows fault of power module?
If your hpmont Inverter indicates a fault in the power module, it could be due to a short circuit between output phases, a short circuit to the ground, an excessively high output current, or damage to the power module itself. Try these steps: * Verify the connection and ensure the wire is properly connected for each phase. * Check the connection to ground and ensure it is correctly wired. * Inspect the connection and mechanism.
What causes a stall overvoltage in hpmont Inverter?
Stall overvoltage in your hpmont Inverter can occur if the bus voltage is too high or the stall overvoltage setting is too low. To fix this: * Check the power input or the function of the brake. * Set the value of stall overvoltage properly using parameter F19.19.
Why is my hpmont Inverter motor overloading?
Your hpmont Inverter's motor might be overloading due to an improper setting of the V/f curve, low mains supply voltage, prolonged operation with a heavy load at low speed, or blocked torque/excessive load. To resolve this: * Adjust the setting of the V/f curve using parameters F09.01 - F09.06. * Check the power input. * Consider using a special motor. * Inspect the load and mechanical transmission devices.
How to fix hpmont HD09-4T2P2G acceleration overcurrent?
Inverter acceleration overcurrent in your hpmont device can occur due to improper connection between the inverter and motor, incorrect motor parameters, an inverter rating that's too small, or an acceleration/deceleration time that's too short. Here’s how to troubleshoot: * Ensure the inverter and motor are properly connected. * Set the correct motor parameters using settings F08.00 - F08.03. * Choose an inverter with a higher rating. * Set appropriate acceleration and deceleration times (F03.01, F03.02).
What to do if hpmont HD09-4T2P2G Inverter shows DC bus over voltage during acceleration?
If your hpmont Inverter displays a DC bus acceleration overvoltage error, it could be due to several factors: the input voltage being too high, a deceleration time set too short, improper wiring leading to hardware overvoltage, or an incorrect selection of braking devices. Here’s how to address it: * Verify the power input. * Set a proper value for deceleration time using parameter F03.02. * Inspect the wiring and ensure it is correctly wired. * Select braking devices according to the recommendations.
Explains safety symbols and their meanings within the manual.
Specifies qualifications for personnel performing installation and maintenance.
Outlines environmental and spatial requirements for inverter installation.
Critical steps to ensure the power supply is safely disconnected before wiring.
How to set and manage user passwords and parameter protection.
Configuration for PID control, including feedback sources and gains.
Inputting and auto-tuning motor parameters for optimal performance.
Configuration for overload and output phase fault protection.
Lists common faults, their reasons, and counter-measures.
Parameters for user password, menu mode, and parameter copying.
Configuration for PID control, including gains, limits, and characteristics.
Motor rated parameters and auto-tuning settings.
Configuration of digital input and output terminals for various functions.
Configuration of analog input (AI) and output (AO) terminals.
Configuration for overload and output phase fault protection.
To Next Page
General