To Next Page
A
Angela OconnorAug 18, 2025
What to do if the HSM Paper Shredder says overload?
- JJoy FordAug 18, 2025
If the motor of your HSM Paper Shredder was overloaded, let the shredder cool down for approximately 15–20 minutes before using it again.
What to do if the HSM Paper Shredder says overload?
If the motor of your HSM Paper Shredder was overloaded, let the shredder cool down for approximately 15–20 minutes before using it again.
How to fix a paper jam in HSM Paper Shredder?
If your HSM Paper Shredder has a paper jam, here are a few things you can try: * If you fed too much paper, press the reverse button “R” to remove the stack. * Take half the stack of paper and try again. * Feed the paper in portions instead of all at once.
What to do if the HSM securio AF150 shredded material container is full?
Empty the shredded material container of your HSM Paper Shredder.
Why is the motor not running on my HSM securio AF150 Paper Shredder?
The motor of your HSM Paper Shredder might not be running because: * There has been a paper jam in the autofeed magazine for more than 2 minutes. See troubleshooting above. * If the motor runs continually (e.g., due to a permanently broken light barrier), it switches off after 60 minutes.
What to do if the HSM Paper Shredder container or safety element is open?
Make sure that you insert the shredded material container correctly in the base cabinet and fold back the safety element of your HSM Paper Shredder.
Why does the HSM Paper Shredder motor run continually?
The motor of your HSM Paper Shredder usually runs continually without taking paper from the stack because of paper clips or staples in the paper stack. Remove the paper clips or staples from the paper, and load the stack again.
What does flashing light mean on HSM Paper Shredder?
A flashing light on your HSM Paper Shredder indicates a fault has occurred while shredding paper. Pull the paper out of the slot to clear the light barrier.
What to do if my HSM securio AF150 says overload?
If the motor of your HSM Paper Shredder is overloaded, allow the shredder to cool down for approximately 15–20 minutes before resuming use.
What to do if my HSM Paper Shredder has a paper jam?
If your HSM Paper Shredder is experiencing a paper jam, try the following: * Press the reverse button “R” to remove the stack of paper, if necessary. * Reduce the stack of paper by half. * Feed the paper in smaller portions. * If using the automatic feed, open the tray and remove any paper clips or staples.
What to do if shredded material container is full in HSM securio AF150 Paper Shredder?
To resolve this issue with your HSM Paper Shredder: * Empty the shredded material container. * Briefly press the reverse button before removing the container; this pulls some material back into the cutting apparatus.
Provides guidance on safe operation and warnings for potential hazards.
Alerts to the danger of cuts from the shredder blades. Keep hands away.
Warns against loose clothing, hair, or jewelry near the feed opening.
Details restrictions for use by children and those with limited capabilities, emphasizing supervision.
Warns about the risk of electric shock due to improper handling of the machine.
Covers correct usage, material compatibility, and warranty terms.
States HSM guarantees spare parts availability for 10 years after model discontinuation.
Diagram and list identifying key parts like feed opening and container.
Explains control buttons and status indicators like 'Ready for operation'.
Details the meaning of indicators for 'Container full', 'Cutting unit blocked', etc.
Covers essential checks before first use, including power and environment.
Guides the user through the process of setting up the automatic feed tray.
Instructions for powering on the document shredder.
Details how to feed paper manually into the shredder's feed opening.
Explains how to use the automatic feeder for multiple sheets.
Initiates permanent mode by holding the operation button for 4 seconds.
Guidelines for shredding CDs and credit cards, including safety warnings.
Details the continuous operation mode and how to activate/cancel it.
Explains the automatic power-saving standby mode and its reactivation.
Step-by-step instructions for safely powering down the shredder.
Provides measures for clearing paper jams and overload conditions.
Explains how to address general fault indicators and container issues.
Details how to clean the shredder and oil the cutting unit.
Provides guidance on environmentally responsible disposal of electronic waste.
Lists items included in the package and available accessories.
Presents specifications like cut size, security level, capacity, and dimensions.
Confirms compliance with EU directives for safety and EMC.
Provides contact details for HSM offices worldwide.
General| Noise level | 56 dB |
|---|---|
| Basket volume | 35 L |
| Product color | White |
| Shredding CDs | No |
| Working width | 241 mm |
| Shredding size | 1.5 mm |
| Shredding type | Cross shredding |
| Shredding staples | - |
| Shredding paper clips | Yes |
| Security level (paper) | 4 |
| Power consumption (typical) | 500 W |
| Dimensions (WxDxH) | 393 x 381 x 740 mm |
| Power requirements | 115 V, 60 Hz |
Weight and Dimensions| Weight | 19323 g |
|---|
