To Next Page
C
Christina CortezSep 8, 2025
What to do if the converter is overloaded on my HTC DURATIQ RX6 Floor Machine?
- CCarrie MccormickSep 8, 2025
If the converter is overloaded on your HTC Floor Machine, let the machine cool down.
What to do if the converter is overloaded on my HTC DURATIQ RX6 Floor Machine?
If the converter is overloaded on your HTC Floor Machine, let the machine cool down.
What to do if the cooling flange for the frequency converter is overheated on my HTC DURATIQ RX6 Floor Machine?
If the cooling flange for the frequency converter is overheated on your HTC Floor Machine, let the frequency converter cool down.
What to do if my HTC Floor Machine will not start?
If your HTC Floor Machine won't start, there are several potential causes: * A fault on the power supply: Check the voltage on the incoming phase/phases. * The power supply indication is not lit: Check the miniature circuit breaker F1. * The main circuit board is not lit: Check the fuse. * The standby LED on the control panel is not lit: Check fuses F2 and F8.
What causes my HTC Floor Machine to lose contact with other units?
If your HTC Floor Machine loses contact with other units, the CAN bus signal may be broken. Check the cable connections on the connection panel.
What to do if there is a low water level in the tank of my HTC DURATIQ RX6 Floor Machine?
If there is a low water level in the tank of your HTC Floor Machine, top up the water and check the level sensor.
How to reset the emergency stop on my HTC DURATIQ RX6?
To reset the emergency stop on your HTC Floor Machine, reset the emergency stop button. Check the remote control and reconnect the radio using the connection button.
How do I fix an error on the CAN bus of my HTC DURATIQ RX6?
To fix an error on the CAN bus of your HTC Floor Machine, check the cabling and the units connected to the HMI.
What to do if the grinding motor overheats in my HTC Floor Machine?
If the grinding motor overheats in your HTC Floor Machine, check the motor's cooling fan and reduce the motor's load. Refer to the meter for motor current.
How to troubleshoot low input voltage to my HTC Floor Machine?
To troubleshoot low input voltage to your HTC Floor Machine, check the voltage level during operation, the cable area, and the electrical supply.
What should I do if the grinding motor is overloaded on my HTC DURATIQ RX6?
If the grinding motor is overloaded on your HTC Floor Machine and the overload meter exceeds 90%, reduce the motor's load. Refer to the meter for motor current.
Outlines essential safety rules and responsibilities for machine operators and users.
Information on measured vibration levels and permitted exposure times for operators.
Explanation of the Human-Machine Interface (HMI) controls and their functions.
Details the various indicators and readouts on the machine's information display panel.
Guidance on how to position and adjust the machine's weights for optimal grinding pressure and balance.
How to maneuver and control the machine using the control panel during grinding.
Detailed steps for operating the machine in manual grinding mode.
Explanation of the emergency stop switch's function and proper usage.
Detailed explanation of the radio remote control, receiver, and their operational procedures.
Instructions for charging, operating via radio, and locking wheels.
Comprehensive guide to setting up and using the radio control system for machine operation.
Information on authorized repair services and contacting retailers for servicing.
Troubleshooting steps for when the machine fails to start or experiences power supply problems.
Troubleshooting steps for recurring issues with fuses or earth fault breakers tripping.
Remedies for situations where the machine is not performing optimally or is overloaded.
Explanation of warning (yellow) and error (red) messages displayed on the machine.
Details on red error messages, machine stops, and how to attempt resetting errors.
General| Model | DURATIQ RX6 |
|---|---|
| Category | Floor Machine |
| Power Source | Electric |
| Weight | 240 kg / 529 lbs |
| Frequency | 50 Hz / 60 Hz |
| Working Width | 600 mm |
| Grinding Width | 600 mm |
