HTP EL-110 - User Manual

85 pages

To Next Page

To Next Page

Loading...

120 Braley Rd. P.O. Box 429 East Freetown, MA 02717-0429 www.htproducts.com

LP- 293 REV. 9.2.14

Elite

INSTALLATION

START-UP

MAINTENANCE

PARTS

Models*

EL-80 / 110 / 150 / 220 / 299 / 301 / 399

*A suffix of “LP” denotes propane gas

*A suffix of “N” denotes natural gas

Heat Exchanger Bears the ASME “H” Stamp

NOTICE: HTP reserves the right to make product changes or updates without notice and will not be held liable for typographical errors

in literature.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

This manual must only be used by a qualified heating installer/service technician. Read all instructions in this manual before installing.

Perform steps in the order given. Failure to comply could result in substantial property damage, severe personal injury, or death.

Table of Contents

Other manuals for HTP EL-110

Installation Start-Up Maintenance Parts73 pages

Questions and Answers

W
whitejaredSep 8, 2025
How to troubleshoot Fault Code E03 System Sensor Failure on my HTP EL-110 Boiler?
- M
  madeline74Sep 9, 2025
  If your HTP Boiler displays Fault Code E03, it means there's a system sensor failure, possibly due to an open or shorted circuit. Here’s how to troubleshoot: Disconnect the system sensor from the wiring and measure its resistance. Compare the measured resistance to the table to see if it corresponds to the sensor's temperature. If the resistance doesn't match, replace the sensor. If the sensor is OK, disconnect the sensor wiring from both the boiler and the sensor, then check continuity using an ohmmeter. Repair or replace the wiring as necessary.
S
Shaun HamptonAug 23, 2025
What to do if my HTP Boiler shows Fault Code F10?
- N
  Nicole MyersAug 23, 2025
  If your HTP Boiler displays fault code F10, it indicates the flame was lost three times during one demand call. To address this: 1. Monitor the gas pressure to the boiler during operation. 2. Make sure the flame remains stable once lit. 3. Confirm the display changes from “GAS VALVE ON” to “RUN” shortly after ignition. 4. Check the FLAME signal on the status display; it should exceed 1.0 when firing. 5. If the signal is below 1 microampere, clean the flame rectifier and spark probe. 6. If the issue continues and the ‘FLAME’ signal remains below 1.0, replace the flame probe and spark igniter probe. 7. A stable flame signal should read 5.0 to 9.0 after a minute of firing. If unsteady, inspect the burner and its sealing gaskets.
S
suethomasAug 25, 2025
What does Fault Code F01 mean on my HTP EL-110 and how do I fix it?
- J
  Joshua TorresAug 26, 2025
  If your HTP Boiler displays fault code F01, it means a safety interlock switch has tripped. Here's how to troubleshoot: 1. Check if an optional UL 353 LWCO is installed. 2. If so, see if the indicator light shows the LWCO has tripped. 3. If tripped, restore the water level and manually reset the switch and boiler. 4. If there are no optional switches, use an ohmmeter to test each standard switch after turning off the boiler and disconnecting the switch to be tested. Find the tripped switch and investigate the cause, considering that temperature switches often trip due to low water flow or poor heat transfer. 5. If no switches are tripped, push RESET on the boiler. If the F01 code returns after a short run, check the flue for blockage.
W
William StricklandAug 27, 2025
How to fix Fault Code FLU on my HTP Boiler?
- L
  Lisa FrenchAug 27, 2025
  If your HTP Boiler is showing Fault Code FLU, it means there's excessive flue pressure. Here's how to address it: 1. Make sure that the flue is not blocked. 2. Check the switch wiring by applying a jumper in place of the switch. If the code clears with the jumper in place, replace the flue switch and connect the wires to the new switch before running the boiler.
A
Amanda MclaughlinAug 27, 2025
What does Fault Code F00 mean on my HTP EL-110 Boiler?
- W
  William WebbAug 28, 2025
  If your HTP Boiler is displaying fault code F00, it indicates the water in the boiler has overheated. Here’s how to address the issue: 1. Verify the circulator pump is functioning correctly. 2. If the pump is running, ensure there is water in the system and it's circulating properly. Check that all ball valves and zone valves are correctly opened or closed. 3. Observe the temperature/pressure gauge. If the water isn't excessively hot but the message appears, inspect the wiring to the water ECO sensor and repair if needed. If the wiring is fine and the code persists without overheating, replace the ECO sensor.
D
Donald GreenNov 28, 2025
What does Fault Code F11 on my HTP EL-110 mean?
- L
  Latasha BowmanDec 1, 2025
  If your HTP Boiler displays fault code F11, it indicates there's flame present when the control isn't calling for the boiler to run. Here's what to do: 1. Check for a flame through the window. If a flame is present, turn off the gas supply to the boiler at the service valve and replace the gas valve. 2. If the flame signal on the status menu is greater than 1.0 when the burner is off, replace the spark igniter and the flame rectification probe. 3. If the flame return sensor is not present after turning off the gas supply, check the gas valve electrical connection. 4. Repair the condensate system as needed. If condensate has backed up and partially filled the combustion chamber, the refractory wall may be damaged and should be replaced. 5. After taking corrective action, turn the gas ...
R
Robert LopezSep 18, 2025
What does Fault Code F31 mean on my HTP EL-110?
- D
  Deborah MckenzieSep 18, 2025
  If your HTP Boiler displays fault code F31, it indicates there was an error while programming the control, and the memory is corrupt. The control must be re-programmed. If programming does not solve the problem, the control must be replaced.
J
james17Sep 23, 2025
What does Blocking Code E19 mean on my HTP Boiler?
- D
  davidjacksonSep 23, 2025
  If your HTP Boiler displays Blocking Code E19, it means the line voltage frequency is out of range. Inspect the power wiring to the boiler and repair as necessary. If connected to line voltage, notify the power company. If connected to an alternate power source such as a generator or inverter, make sure the line voltage frequency supplied by the device is 60 Hz.
P
Pamela SmithSep 7, 2025
What to do if my HTP EL-110 displays Fault Code PRO?
- J
  james15Sep 7, 2025
  If your HTP Boiler is showing Fault Code PRO, it indicates low water pressure in the boiler. To resolve this: 1. Make sure the system pressure is above 10 psig. 2. Check for leaks in the system piping.
C
Charles BerrySep 5, 2025
What does Fault Code F13 mean on my HTP Boiler?
- P
  Patrick HallSep 5, 2025
  If your HTP Boiler displays fault code F13, it indicates the fan isn't running at the commanded speed. Here's how to troubleshoot: 1. Check the combustion air fan wiring. 2. Measure the DC voltage from the red fan wire to ground while connected to the fan; it should be between 24 to 40 volts. If lower than 24 volts, check for excessive external loads on the boiler sensor terminals. Disconnect the 5-pin plug from the fan and check the voltage on the red wire again. If it's now between 24-40 volts, replace the fan. If it remains below 24 volts, replace the boiler control board.

HTP EL-110 Specifications

General

Brand	HTP
Model	EL-110
Category	Boiler
Language	English

Summary

Installation, Operation, and Maintenance

Start-Up

Guide for initiating boiler operation and initial setup procedures.

Maintenance

Procedures and schedules for keeping the boiler in optimal condition.

Parts

List and identification of components for the boiler unit.

Safety Warnings and Notices

Danger

Imminent hazards that could cause death or serious injury.

Warning

Potentially hazardous situations that could cause death or serious injury.

What to Do If You Smell Gas

Emergency procedures to follow in case of a gas leak.

Operating Instructions

Step-by-step guide for running the boiler safely and correctly.

Related product manuals

Preview: HTP EL-80

Preview: HTP Elite EL-80

HTP Elite EL-80

Preview: HTP ELU Series

Preview: HTP Elite XL ELX-400

HTP Elite XL ELX-400

HTP Elite XL ELX-650

HTP Elite XL ELX-800

HTP Elite XL ELX-500

HTP Elite Ultra ELU-199WCN