Huawei SmartAX MA5603T - Page 548

1. Configure the ADSL2+ line profile.
You can configure it based on your requirements.
huawei(config)#adsl line-profile add 10
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,ETSI)
> 2: Full rate(G992.1/3/5,T1.413,ETSI)
> 3: G.DMT (G992.1/3/5)
> 4: G.HS (G992.1~5)
> 5: ADSL (G992.1~2,ETSI,T1.413)
> 6: ADSL2 & ADSL2+ (G992.3~5)
> Please select (0~6) [1]:
> Trellis mode 1-disable 2-enable (1~2) [2]:
> Bit swap downstream 1-disable 2-enable (1~2) [2]:
> Bit swap upstream 1-disable 2-enable (1~2) [2]:
> Please select the form of transmit rate adaptation downstream:
> 1-fixed, 2-adaptAtStartup, 3-adaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed, 2-adaptAtStartup, 3-adaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set power management parameters? (y/n) [n]:
> Will you set tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 10 successfully
2. Configure the ADSL2+ channel profile.
The configuration data in the ADSL2+ channel profile is set according to the actual channel
conditions.
huawei(config)#adsl channel-profile add 10
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:
> Will you set the minimum impulse noise protection? (y/n) [n]:y
> Minimum impulse noise protection downstream:
> 1-noProtection 2-halfSymbol 3-singleSymbol 4-twoSymbols
> 5-threeSymbols 6-fourSymbols 7-fiveSymbols 8-sixSymbols
> 9-sevenSymbols 10-eightSymbols 11-nineSymbols 12-tenSymbols
> 13-elevenSymbols 14-twelveSymbols 15-thirteenSymbols 16-fourteenSymbols
> 17-fifteenSymbols 18-sixteenSymbols
> Please select (1~18) [2]:4
> Minimum impulse noise protection upstream:
> 1-noProtection 2-halfSymbol 3-singleSymbol 4-twoSymbols
> 5-threeSymbols 6-fourSymbols 7-fiveSymbols 8-sixSymbols
> 9-sevenSymbols 10-eightSymbols 11-nineSymbols 12-tenSymbols
> 13-elevenSymbols 14-twelveSymbols 15-thirteenSymbols 16-fourteenSymbols
> 17-fifteenSymbols 18-sixteenSymbols
> Please select (1~18) [2]:4
> Will you set interleaving delay parameters? (y/n) [n]:y
> Maximum interleaving delay downstream (0~63 ms) [16]:24
> Maximum interleaving delay upstream (0~63 ms) [6]:12
> Will you set parameters for rate? (y/n) [n]:y
> Minimum transmit rate downstream (32~32000 Kbps) [32]:
> Minimum reserved transmit rate downstream (32~32000 Kbps) [32]:
> Maximum transmit rate downstream (32~32000 Kbps) [24544]:8000
> Minimum transmit rate upstream (32~6000 Kbps) [32]:
> Minimum reserved transmit rate upstream (32~6000 Kbps) [32]:
> Maximum transmit rate upstream (32~6000 Kbps) [1024]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 10 successfully
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
7 Example: Subtending Networking
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
523