Need help?Do you have a question about the Humminbird Matrix 12 and is the answer not in the manual?
General| Sonar Type | Dual Beam |
|---|---|
| GPS | No |
| Chartplotting | No |
| Transducer Included | Yes |
| Display Size | 5 inches |
| Sonar Frequency | 200 kHz / 83 kHz |
| Depth Capability | 600 feet |
| Max Depth | 600 feet |
Describes the 200 kHz single beam sonar system for Matrix 10, 12, or 20.
Describes the 200/83 kHz DualBeam PLUS™ sonar system for Matrix 17 or 27.
Describes the QuadraBeam® sonar system for the Matrix 37 Fishing System.
Presents a historical log of sonar returns with depth, temperature, and speed readouts.
Increases display resolution to separate sonar returns that are very close together.
Displays sonar returns from 83 kHz wide beam and 200 kHz narrow beam side-by-side.
Provides digital data in a large, easy-to-see format with depth, temperature, and speed.
Shows sonar information from left/right 90° 455 kHz beams and 200 kHz down-looking beam.
Turns the unit on/off and adjusts backlight and contrast.
Used to access the menu system, including Start-Up, X-Press, and Main Menus.
Used to select menu choices and change menu settings.
Exits menus, cancels alarms, and cycles through views.
Accesses Normal, Simulator, System Status, or PC Connect modes on power up.
Provides quick access to frequently-used settings without navigating the whole menu.
Organizes settings under Alarms, Sonar, Setup, and Accessories tabs.
Controls how much detail is shown on the display by adjusting sonar return detail.
Sets the shallowest depth range displayed on Sonar, Split Sonar, and Big Digits Views.
Sets the deepest depth range that will be displayed on the screen.
Determines the speed at which sonar information moves across the display.
Selects the method used to represent bottom and structure on the display.
Sets the magnification level for the Sonar Zoom View.
Sets which sonar returns from the transducer will be displayed on the screen.
Uses advanced signal processing to interpret sonar returns and display fish symbols.
Adjusts the threshold of the Fish ID+™ detection algorithms.
Sets the RTS™ Window to Wide, Narrow, or Off in the Sonar View.
Changes the sensitivity of the 83 kHz beam.
Adjusts the sensitivity of the 455 kHz beam.
Divides the display into four equal sections separated by horizontal depth lines.
Adjusts the filter that removes surface clutter noise.
Limits interference on the display from various sources.
Adjusts the maximum depth of operation for the Fishing System.
Configures the unit for operation in fresh or salt water.
Allows selection of the transducer to be used.
Sounds when the depth becomes equal to or less than the menu setting.
Sounds when the system detects fish that correspond to the alarm setting.
Sounds when the input battery voltage is equal to or less than the menu setting.
Selects the pitch of the alarm sound.
Selects the units of measure for all depth-related readouts.
Selects the units of measure for all temperature-related readouts.
Selects the units of measure for all distance-related readouts.
Selects the units of measure for speed-related readouts.
Sets the menu system to Normal or Advanced.
Selects the display language for menus.
Resets the Triplog to zero.
Resets ALL menu settings to their factory defaults.
Sets available views to either hidden or visible in the view rotation.
Sets individual digital readouts on the Sonar View.
Adjusts the digital depth readout to indicate depth from waterline or keel.
Adjusts the temperature readout by the amount entered.
Adjusts the speed readout by the percentage entered.
Turns the NMEA output on or off.
Steps to take if the Matrix unit does not power up.
Troubleshooting steps if the unit defaults to Simulator mode with a transducer.
Common conditions causing display problems and possible solutions.
Identifies sources of electrical noise and interference affecting the display.
To Next Page