Need help?Do you have a question about the Humminbird Matrix 20 and is the answer not in the manual?
General| Transducer Type | Single Beam |
|---|---|
| Frequency | 200 kHz |
| Power Output | 100 watts (RMS), 800 watts (peak to peak) |
| GPS | No |
| Water Resistance | Waterproof |
| Display Size | 5 inches |
| Display Type | LCD |
| Max Depth | 600 feet |
| Beam Angle | 20 degrees |
Details the 200 kHz single beam sonar system and its coverage.
Explains the 200/83 kHz DualBeam PLUS sonar system and its coverage.
Describes the QuadraBeam sonar with its wide 90 coverage.
Presents a historical log of sonar returns with depth information.
Magnifies a narrow slice of the full range view for detailed analysis.
Compares 83 kHz wide beam and 200 kHz narrow beam returns.
Displays digital data in a large, easy-to-see format.
Shows sonar from left/right 455 kHz beams and 200 kHz down-looking beam.
Operation of power, backlight, contrast, and view cycling keys.
Used to access the menu system and navigate options.
Allows selection and alteration of menu settings and cursor positioning.
Allows expansion of system functionality with accessories.
Details the procedure to turn on the Matrix Fishing System.
Menu accessed during power up for initial system configuration.
Provides quick access to frequently-used settings.
Organized menu structure with Alarms, Sonar, Setup, and Accessories tabs.
Sets system complexity: Normal for simplicity, Advanced for control.
Describes how view updates immediately after menu setting changes.
On-water operation with a connected transducer.
Allows learning system operation without being on the water.
View system connections and conduct a unit self-test.
Update software using a PC and the PC Connect Cable.
Controls the level of detail by adjusting sonar return display.
Sets the shallowest and deepest depth ranges to be displayed.
Adjusts display speed and representation of bottom/structure.
Sets the magnification level for the Sonar Zoom View.
How to adjust the sensitivity setting for optimal sonar detail.
How to set the shallowest depth range for display.
Adjusts sonar information display speed for detail.
Chooses how bottom and structure are represented on screen.
Sets which sonar returns from the transducer are displayed.
Displays fish symbols and adjusts the threshold for detection.
Configures RTS Window and adjusts beam sensitivities.
Adjusts display lines, filters surface clutter, and sonar noise.
Configures max depth, water type, and selects transducer.
Adjusts threshold for identifying fish based on sonar returns.
Configures the Real Time Sonar Window display.
Changes sensitivity for the 83 kHz beam.
Adjusts sensitivity for the 455 kHz beam.
Limits interference from sources like boat engine or turbulence.
Sets maximum operating depth for performance tuning.
Configures unit for fresh or salt water operation.
Allows selection of the transducer to be used with the system.
Sounds when depth becomes equal to or less than the set value.
Sounds when the system detects fish matching the alarm setting.
Warns when input battery voltage drops below a set threshold.
Selects the pitch of the alarm sound.
Selects units of measure for depth-related readouts.
Selects units for temperature-related readouts (International Only).
Selects units for distance-related readouts (with accessories).
Selects units for speed-related readouts (with accessories).
Sets menu system to Normal or Advanced.
Selects the display language for menus (International Only).
Resets the Triplog data to zero.
Resets all menu settings to factory defaults.
Adjusts digital depth readout for waterline or keel depth.
Adjusts the temperature readout by a specified amount.
Adjusts the speed readout by a percentage.
Turns NMEA data output on or off.
Steps to troubleshoot when the unit fails to power on.
Troubleshooting transducer detection issues causing simulator mode.
To Next Page