Hunter H45DS - Page 151

Hunter 45
DS
• En
g
ines and Transmissions
1
1.
3
Important: Engines are not warranted by Hunter Corporation,
these warranties are written by the engine manufacturers.
DANGER
! !
Wh
en occup
yi
n
g
t
h
e en
gi
ne room, or an
y
area t
h
at
m
echanical equipment ma
y
be located, alwa
y
s be
a
ware of movin
g
parts or components. Death o
r
dismemberment ma
y
be the result of bein
g
cau
g
ht in
m
ovin
g
machiner
y.
Important: Engines require air to operate. For this reason, do
not operate the engine or generator with this area obstructed.
Important: The engine manual supplied by the manufac-
turer includes complete and detailed information about oper-
ating and maintaining your boat’s engines. Be sure to read
it. Do not start or operate the boat’s engines until you
have done so. The life and performance you receive from
your engines depends greatly on the way you care for it.
1
1.1.1 En
g
ine Mounts
The en
g
ine mounts supplied with
y
our boat are manu-
factured b
y
the en
g
ine manufacturer. These mounts are
desi
g
ned speci
f
icall
y
f
or the en
g
ine in which the
y
are
a
tt
ac
h
ed
.
M
ost en
g
ine mounts are desi
g
ned
f
or ad
j
ustment side-
wa
y
s as well as vertical. Vertical ad
j
ustment nuts lock
u
p
or
d
own on t
h
e t
h
rea
d
e
d
vert
i
ca
l
stu
d
, w
i
t
h
a s
l
ot
provided to allow side to side ad
j
ustment on the en
g
ine.
Important: It is advisable to spray a protective coating on the
studs to prevent corrosion.
M
an
y
factors warrant the size and t
y
pe of en
g
ine mounts
th
a
t
a
r
e
used
. Th
ese
m
ou
nt
s
a
l
so
co
nt
a
in i
so
l
a
t
o
r
s
whi
c
h
isolate the en
g
ine
f
rom the boat or strin
g
ers to dampen
vibration, noise. and other undesirable effects from
e
n
g
ines. For more in
f
ormation about the en
g
ine mounts
see the en
g
ine manu
f
acturers manuals.
1
1.1.2 En
g
ine Controls
Th
e en
gi
ne contro
l
s on
y
our
b
oat are
l
ocate
d
on t
h
e
steerin
g
pedestal.
The strai
g
ht up position is neutral, shift forward to
g
o
f
orward, movin
g
f
urther
f
orward increases the speed.
M
ove the lever backwards for reverse, the same as for-
w
a
r
d
m
o
r
e
m
o
v
e
m
e
nt in th
e
r
e
v
e
r
se
d
ir
ec
ti
o
n in
c
r
eases
the en
g
ine speed.
P
ress and hold the center button on the shi
f
t lever, and
move the lever
f
orward to increase the en
g
ine RPM
without shiftin
g
into
g
ear.
1
1.1.3 En
g
ine Monitorin
g
CAUTION
! !
Alwa
y
s monitor
y
our boats oil pressure, and
water temp. while underwa
y
, even if
y
ou
r
e
n
gi
nes are equ
i
ppe
d
w
i
t
h
an a
l
arm s
y
stem t
o
monitor these.
Shut down the en
g
ines immediatel
y
if the
g
au
g
es
are not in normal ran
g
es or an alarm sounds.
D
o not restart
y
our en
gi
nes unt
il
t
h
e pro
bl
em
i
s
c
orrected
.
For information on the correct levels for en
g
ine runnin
g
,
please consult
y
our en
g
ine owner’s manuals
f
rom the
e
n
g
ine manu
f
acturer in
y
our owner’s packet.
Important: The Hour meter will run if you leave the ignition
switch on when the engine is not running. This unnecessarily
increases the number of engine hours.
Note: Instruments have a tolerance for accuracy. In addition,
each engine may operate at differing values at the same RPM.
As long as the instruments are reading within the proper operat-
ing range, the engine is operating properly.
1
1.1.4 En
g
ine Coolin
g
Fi
g
. 11.
1