Hunter H45DS - Anchoring and Thruster Systems

Hunter 4
5
DS
• Underwater Gea
r
6.5
C
are should be taken that these intakes and pick ups are
c
leaned of barnacles and other
g
rowth as specified in the
maintenance section o
f
this manual to maintain a clear,
open
passage
w
ay
.
STREET ELL
TYP. THRU-HULL W/ SEACOCK DETAIL
THROUGH HULL
O
UGH HULL NUT
HOSE BARB
3/4 (19 MM)
PLYWOOD BACKING
HULL
DOUBLE CLAMPED
HOSE
BALL VALVE
O
The optional electronics packa
g
e
y
ou have ordered on
y
our boat will lar
g
el
y
determine the underwater
g
ear that
is related to the monitorin
g
equipment. Be sure and refer
to
y
our documentation in
y
our owner’s packet to
f
ind out
the details about this equipment
.
6.4 Windlass and Anchorin
g
(
Option
)
6.4.1 Windlass
The windlass facilitates the anchorin
g
of
y
our boat b
y
automat
i
ca
lly
ra
i
s
i
n
g
an
d
l
ower
i
n
g
t
h
e anc
h
or.
T
o oper-
ate the windlass, the windlass breaker at the batter
y
switch panel must be switched on.
Note: It is important that the windlass clutch is tight for proper
operation and safety. Periodically check the clutch and tighten
if necessary.
T
o t
igh
ten t
h
e c
l
utc
h:
With the anchor in the stowed position, ti
g
hten the
w
i
n
dl
ass c
l
utc
h
by
i
nsert
i
n
g
t
h
e emer
g
enc
y
h
an
dl
e
i
n
the clutch nut.
(S
ee
f
i
g
6.9
)
and turn clockwise.
T
o Operate Manuall
y:
M
ake sure that the safet
y
hook is removed from the
•
a
n
c
h
o
r
c
h
a
in
.
I
nsert t
h
e emer
g
enc
y
h
an-
d
l
e
int
o
th
e
c
l
u
t
c
h n
u
t
.
Tu
rn
ha
n
dle
clock
w
ise
t
o
r
e
tri
e
v
e
a
n
c
h
o
r.
T
o o
p
erate from the
bow
:
S
witch the
p
ower on at
th
e
co
ntr
o
l
s
R
emove the safet
y
h
ook
Lift the
p
rotective ca
p
f
r
o
m th
e
foo
t
s
wit
c
h
a
n
d
depress the up or down
s
wit
c
h f
o
r th
e
des
ir
ed
r
esu
lt.
M
aintenance
:
DANGER
! !
M
ake sure that the power is off before performin
g
a
n
y
ma
i
ntenance or wor
k
on t
h
e w
i
n
dl
ass
.
P
eriodicall
y
check the motor and control box electrical
c
onnect
i
ons, remove an
y
res
id
ue an
d
cover connect
i
ons
with a small coatin
g
o
f
g
rease.
I
t
i
s recommen
d
e
d
t
h
at
y
ou, once a
y
ear,
di
sassem
bl
e
the windlass and remove residue buildup. To per
f
orm
this maintenance
f
ollow all sa
f
et
y
procedures and com-
plete the followin
g:
U
sin
g
the emer
g
enc
y
handle, unscrew the nut b
y
turn
i
n
g
t
h
e
h
an
dl
e counterc
l
oc
k
w
i
se.
R
emove the drum, upper cone, chain wheel, and
lo
w
e
r
co
n
e.
Wash down with water to remove an
y
residu
e
C
oat sur
f
aces with a li
g
ht
f
ilm o
f
lubrican
t
•
•
•
•
•
•
•
•
•
Fi
g
. 6.
8
Emergency Handle
Clutch Nut
Drum
Upper Cone
Chain Pulley
Lower Cone
Windlass Profile Illustration
Fi
g
. 6.9