N
nicole99Aug 12, 2025
What does it mean when the charging LED flashes red on my Husqvarna 240i Chainsaw?
- LLori RobersonAug 13, 2025
If the charging LED flashes red on your Husqvarna Chainsaw, it indicates a faulty battery. Speak to your dealer.
To Next PageTo Next PageWhat does it mean when the charging LED flashes red on my Husqvarna 240i Chainsaw?
If the charging LED flashes red on your Husqvarna Chainsaw, it indicates a faulty battery. Speak to your dealer.
What to do if the warning indicator flashes on my Husqvarna 240i Chainsaw?
If the warning indicator on your Husqvarna Chainsaw is flashing, it could be due to several reasons: * The chain brake might be engaged. If so, disengage the chain brake. * There could be a temperature deviation. Allow the product to cool down. * The saw chain might be overloaded and unable to move. Release the saw chain. * The power trigger and the start/stop button may have been pushed simultaneously. Release the power trigger to activate the product.
Why is the charging LED flashing green on my Husqvarna 240i?
If the charging LED on your Husqvarna Chainsaw flashes green, it indicates a temperature deviation. The battery is either too cold or too hot to charge or use. Allow the battery to cool down or warm up. Once the battery reaches the correct temperature, you can use or charge it again. Make sure to use the battery charger in ambient temperatures between 5 °C (41 °F) and 40 °C (104 °F).
How to fix a flashing green activate LED on a Husqvarna Chainsaw?
If the green activate LED is flashing on your Husqvarna Chainsaw, it indicates low battery voltage. To resolve this, charge the battery.
Why is the green activate LED flashing on my Husqvarna Chainsaw?
If the green activate LED is flashing on your Husqvarna Chainsaw, it indicates low battery voltage. To resolve this, charge the battery.
How to fix a Husqvarna 240i Chainsaw when the green LED flashes?
If the green LED is flashing on your Husqvarna Chainsaw, it means the battery voltage is low. You should charge the battery.
What does it mean when the charging LED flashes green on my Husqvarna 240i Chainsaw?
If the charging LED flashes green on your Husqvarna Chainsaw, it signifies a temperature deviation. The battery is either too cold or too hot to charge or use. Allow the battery to cool down or warm up. Once the battery reaches the correct temperature, you can use or charge it again. Ensure you use the battery charger in ambient temperatures between 5 °C (41 °F) and 40 °C (104 °F).
What to do if the error LED flashes on my Husqvarna Chainsaw?
If the error LED flashes on your Husqvarna Chainsaw, it could be due to the following reasons: 1. Temperature deviation: Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). 2. Too much voltage: Ensure that the mains voltage matches the voltage of the product, referring to the rating plate on the product. 3. Remove the battery from the battery charger.
General| Power source | Battery |
|---|---|
| Battery voltage | 36 V |
| Chain speed at max power | 15 m/s |
| Chain pitch | 3/8 inch |
| Chain gauge | 1.1 mm |
| Bar Length | 12-14 inches |
| Chain Speed | 15 m/s |
| Engine Power | Not applicable |
| Fuel Tank Capacity | Not applicable |
| Oil Tank Capacity | 0.2 L |
| Recommended bar length | 35 cm (14") |
Steps to attach the guide bar and saw chain, with options for bar knob or bolt.
Perform checks on the chain brake, guards, trigger, and keypad before operation.
Addresses frequently asked questions regarding kickback and chain brake engagement.
Describes basic cutting strokes and body positioning for different cuts.
Lists possible faults and solutions for the product's LED screen.
Lists possible faults and solutions for battery LED indicators.
