Why is my Husqvarna 365 X-Torq difficult to start?
If you're having difficulty starting your Husqvarna Chainsaw, possible solutions include adjusting the L screw, checking for a blocked air filter, or addressing issues with the choke (such as it not working, or having a worn pivot or valve). Other potential causes are a blocked fuel filter or fuel line, a seized piston ring, or a blocked impulse channel.
What causes carburettor leaking fuel in Husqvarna 365 X-Torq Chainsaw?
If the carburettor of your Husqvarna Chainsaw is leaking fuel, it could be due to a loose or faulty fuel pipe, a hole in the diaphragm, a worn needle valve, a sticking needle valve assembly, or a needle valve set too high. Other potential causes include a leak in the metering system or a loose cover on the carburettor pump side.
Why is my Husqvarna 365 X-Torq not idling?
If your Husqvarna Chainsaw won't idle, consider these possible solutions: adjust the L screw, check for a leaking air intake hose, ensure the carburettor mounting bolts are tight, and inspect the fuel hose for looseness or faults. Also, check for a blocked fuel filter, fuel line, or fuel tank vent. Other potential causes include a stiff throttle valve pivot, a sticking throttle pushrod, a defective throttle return spring, a bent throttle stop, or a faulty dif ufser jet.
What to do if my Husqvarna 365 X-Torq Chainsaw engine stalls when throttle released?
If your Husqvarna Chainsaw engine stalls when you release the throttle, try adjusting the L and H screws. Other possible causes include a faulty pump diaphragm, a needle valve set too high, a needle valve assembly sticking, or faulty dif ufser jets.
How to fix over rich acceleration in Husqvarna 365 X-Torq Chainsaw?
To address over rich acceleration in your Husqvarna Chainsaw, consider adjusting the L and H screws. Also, check for a blocked air filter, a faulty pump diaphragm, or faulty dif ufser jets.
Why is my Husqvarna 365 X-Torq idling uneven?
If your Husqvarna Chainsaw is idling unevenly, check the fuel filter and fuel line for blockages. Also, inspect the air intake hose for leaks and ensure the carburettor mounting bolts are tight. Other potential causes include a worn throttle valve pivot or valve, a loose throttle valve screw, a sticking needle valve assembly, a leak in the metering system, a worn metering system centre knob, a hole in the diaphragm, a leaking control diaphragm/cover plate, or a crankcase leak.
How to fix Husqvarna 365 X-Torq Chainsaw idling too rich?
To fix an idling that is too rich on your Husqvarna Chainsaw, try adjusting the L screw. It could also be caused by a worn needle valve or lever, a needle valve set too high, a leaking control diaphragm/cover plate, or a needle valve assembly sticking.
Why is my Husqvarna Chainsaw will not run at full throttle?
If your Husqvarna Chainsaw won't run at full throttle, start by adjusting the H screw. Also, check for a blocked air filter, fuel tank vent, or fuel filter. Other potential causes include a blocked or leaking fuel line or impulse channel, a loose or damaged fuel hose, a loose cover on the carburettor pump side, or a faulty pump diaphragm. Additionally, inspect for a leaking air intake hose, loose carburettor mounting bolts, a needle valve set too low, a damaged or incorrectly assembled metering system, a sticking needle valve assembly, or a blocked silencer.
What causes flooding when engine not running in Husqvarna 365 X-Torq?
If your Husqvarna Chainsaw is flooding when the engine isn't running, it could be due to a worn needle valve, a needle valve set too high, or a needle valve assembly sticking.
Why L screw requires constant adjustment in Husqvarna 365 X-Torq Chainsaw?
If the L screw on your Husqvarna Chainsaw requires constant adjustment, it could be due to a blocked fuel line, a needle valve set too high, a needle valve assembly sticking, a leak in the metering system, or a leaking control diaphragm/cover plate. Other potential causes include faulty dif ufser jets or a crankcase leak.
General| Cylinder Displacement | 70.7 cm³ |
|---|---|
| Weight | 6.4 kg |
| Chain Pitch | 3/8" |
| Fuel Tank Volume | 0.77 l |
| Chain Gauge | 0.058 " |
| Bar Length | 18-28 inches |
To Next Page
