Husqvarna 455e rancher ii User Manual

44 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

EE

EE

nn

nn

gg

gg

ll

ll

ii

ii

ss

ss

hh

hh

455 Rancher II,

455e Rancher II

455e Rancher II

TrioBrake

460 Rancher II, 465 Rancher II

Oper

ator

′

s manual

Please r

ead the operator’s manual carefully and make sure you understand the instructions before using the machine.

Table of Contents

Other manuals for Husqvarna 455e rancher ii

Workshop Manual60 pages

Questions and Answers:

P
Patricia FloydAug 16, 2025
Why is my Husqvarna 455e rancher ii Chainsaw difficult to start?
- D
  David TrujilloAug 16, 2025
  If your Husqvarna Chainsaw is difficult to start, several factors could be at play. Start by checking the air filter and clean or replace it if it's blocked. Ensure the choke is functioning correctly; repair or replace it if necessary, and consider replacing the choke axle or valve if they are worn. Also, a blocked fuel filter requires cleaning or replacement, and a blocked fuel line needs inspection and clearing. Finally, inspect and free the piston ring if it's stuck, and clear any blockage in the impulse channel.
S
Sarah TaylorAug 19, 2025
Why is the carburetor leaking fuel on my Husqvarna Chainsaw?
- B
  blankenshipraymondAug 19, 2025
  If your Husqvarna chainsaw's carburetor is leaking fuel, the issue might stem from a loose or faulty fuel pipe (tighten or replace the pipe), a hole in the membrane (replace the membrane), or a binding control system (inspect and fix the control system). Also, the control system might be set too high (adjust the control system), there might be a leak in the control system (inspect and repair the control system), or the cover on the carburetor pump side might be loose (tighten the cover).
M
Mrs. Tara NolanAug 22, 2025
How to fix uneven idling on my Husqvarna 455e rancher ii?
- J
  Joseph WarrenAug 22, 2025
  If your Husqvarna Chainsaw is idling unevenly, there are several potential causes: * A blocked fuel filter: Replace or clean it. * A blocked fuel line: Inspect and clear it. * A leaking inlet hose: Replace the hose. * Loose carburetor clamping screws: Tighten the screws. * A worn throttle valve shaft, throttle valve screw, or throttle valve: Replace the respective part. * A leaking control system: Inspect and repair it. * A worn control system center knob: Replace the knob. * A hole in the membrane: Replace the membrane. * A leaking control diaphragm/cover plate: Inspect and replace the diaphragm or plate. * A leaking crankcase: Inspect and repair the crankcase.
M
mark28Aug 26, 2025
What to do if my Husqvarna 455e rancher ii does not idle?
- B
  Benjamin WalkerAug 26, 2025
  If your Husqvarna Chainsaw is not idling, check the following: a leaking inlet hose (replace the hose), loose carburetor clamping screws (tighten the screws), or a loose or faulty fuel pipe (tighten or replace the fuel pipe). Also, check for a blocked fuel filter (replace or clean), a blocked fuel line (inspect and clear), or a blocked tank ventilator (clear the ventilator). Inspect and free an inert throttle valve shaft, and inspect and fix a binding throttle stay. Replace a defective throttle return spring, and straighten or replace a bent valve axle stop. Finally, replace a faulty diffuser jet.
C
Colin YoungAug 28, 2025
Why is my Husqvarna 455e rancher ii low on power?
- U
  uhoffmanAug 28, 2025
  If your Husqvarna chainsaw is low on power, consider these possible causes: a clogged tank vent (clear the venting), a blocked fuel filter (replace or clean the filter), or a leaking or blocked impulse channel (inspect and repair, or clear the channel). Also, check for a loose cover on the carburetor pump side (tighten the cover), a faulty pump diaphragm (replace the diaphragm), or a blocked air filter (clean or replace the filter). Additional possibilities include a binding, leaking, or incorrectly assembled control system (inspect and fix, inspect and repair, or disassemble and reassemble, respectively), a loose diaphragm rivet (tighten the rivet), a hole in the membrane (replace the membrane), or a leaking control diaphragm/cover plate (inspect and replace the diaphragm or cover plate).
S
Sarah OchoaAug 31, 2025
What to do if my Husqvarna 455e rancher ii Chainsaw engine stops when releasing the throttle?
- J
  Jessica HouseAug 31, 2025
  If the engine of your Husqvarna Chainsaw stops when releasing the throttle, it could be due to a faulty pump diaphragm (replace it), a control system set too high (adjust it), a binding control system (inspect and fix it), or a faulty diffuser jet (replace it).
M
michaeljohnsonSep 12, 2025
Why is my Husqvarna 455e rancher ii Chainsaw accelerating too rich?
- W
  Wendy RiosSep 12, 2025
  If your Husqvarna Chainsaw has too rich acceleration, it may be due to a blocked air filter (clean or replace the air filter), a faulty pump diaphragm (replace the pump diaphragm), or a faulty diffuser jet (replace the diffuser jet).

Husqvarna 455e rancher ii Specifications

General

Brand	Husqvarna
Model	455e rancher ii
Category	Chainsaw
Language	English

Related product manuals

Preview: Husqvarna 455e Rancher

Husqvarna 455e Rancher

Preview: Husqvarna 455 Rancher II

Husqvarna 455 Rancher II

Husqvarna 465 Rancher II

Preview: Husqvarna 455 Rancher

Husqvarna 455 Rancher

Preview: Husqvarna Rancher 455

Husqvarna Rancher 455

Husqvarna 450 Rancher

Preview: Husqvarna 460 Rancher

Husqvarna 460 Rancher

Preview: Husqvarna 445 Rancher

Husqvarna 445 Rancher

Preview: Husqvarna 50 Rancher

Husqvarna 50 Rancher

Preview: Husqvarna 55 Rancher

Husqvarna 55 Rancher

Preview: Husqvarna Rancher 55

Husqvarna Rancher 55

Preview: Husqvarna 450