Husqvarna 562XP Mark II

Questions and Answers

B
Bruce WilliamsJul 30, 2025
Why won't my Husqvarna 562XP Mark II engine start?
- A
  Adam DavisJul 30, 2025
  Several factors can prevent your Husqvarna Chainsaw engine from starting. It could be due to blocked starter pawls, which may need adjustment or replacement. The fuel type might be incorrect, requiring you to drain the tank and refill it with the correct fuel. A dirty or wet spark plug can also be the culprit, so ensure it's clean and dry. Other potential issues include an incorrect electrode gap (clean the spark plug and ensure correct gap and spark plug type), a loose spark plug (tighten it), or a fuel tank filled with chain oil (drain if you haven't tried starting; otherwise, consult your servicing dealer).
M
Marcus StuartAug 5, 2025
How to fix a flooded Husqvarna 562XP Mark II engine?
- G
  Gloria BennettAug 5, 2025
  If your Husqvarna Chainsaw engine is flooded due to repeated starts with full choke after ignition, remove and clean the spark plug. Then, position the chainsaw on its side with the spark plug hole facing away from you. Pull the starter rope handle 6-8 times. Finally, reassemble the spark plug and attempt to start the chainsaw.
W
wcoffeyAug 13, 2025
What to do if my Husqvarna 562XP Mark II Chainsaw engine starts but stops again?
- A
  Andrea CrawfordAug 13, 2025
  If your Husqvarna Chainsaw engine starts and then stops, the issue might stem from incorrect fuel, in which case you should drain the fuel tank and refill it with the correct fuel. Alternatively, try cleaning or replacing the air filter, or replacing the fuel filter.
S
Sandra Freeman MDAug 21, 2025
What to do if the spark plug is dirty in Husqvarna 562XP Mark II?
- D
  David WuAug 21, 2025
  If the spark plug in your Husqvarna Chainsaw is dirty, clean the spark plug and make sure that the electrode gap and spark plug is correct, and that the correct spark plug type is the recommended or equivalent. Tighten the spark plug.

Summary

Introduction to Husqvarna Chainsaw

Intended Use of Chainsaw

Specifies the chainsaw's design for forest service work like felling, limbing, and cutting.

Product Description

Introduces the Husqvarna 562XP Mark II/562XPG Mark II as combustion engine chainsaw models.

Chainsaw Safety Guidelines

Safety Definitions & General Instructions

Explains warnings, cautions, and general safety rules for product use.

Operational Safety & PPE

Guides on safe operation, kickback avoidance, and required protective equipment.

Safety Device Checks

Instructions for verifying the proper function of safety devices like the chain brake.

Chainsaw Assembly Instructions

Assembly Introduction

Read safety chapter before assembling the product.

Guide Bar & Saw Chain Assembly

Step-by-step instructions for attaching the guide bar and saw chain to the chainsaw.

Spiked Bumper Assembly

Instructions for attaching a spiked bumper; consult dealer if needed.

Chainsaw Operation Guide

Pre-Operation Checks & Fueling

Ensuring readiness by checking the product and correctly fueling the chainsaw.

Kickback Information

Understanding kickback causes, risks, and basic prevention methods.

Starting, Stopping & Cutting Basics

Steps for starting, stopping, and performing basic cutting techniques with the chainsaw.

Advanced Cutting & Felling Techniques

Techniques for cutting trunks, limbing, felling trees, and handling tension.

Chainsaw Maintenance Procedures

Scheduled Maintenance & Safety Checks

Overview of daily, weekly, monthly tasks and checks of safety devices.

Cutting System Maintenance

Procedures for cleaning air filter, spark plug, sharpening chain, and adjusting settings.

Lubrication & Component Care

Checking chain lubrication, rim sprocket, needle bearing, guide bar, and adjusting oil flow.

Chainsaw Troubleshooting Guide

Engine Start Failures

Diagnosing and resolving issues when the engine fails to start.

Engine Stalling Problems

Troubleshooting for when the engine starts but then stops unexpectedly.

Transportation and Storage

Safe Storage & Transport Procedures

Guidelines for safe transport and preparing the product for long-term storage.

Technical Data

Product Specifications and Performance

Detailed specifications for engine, fuel system, weight, and chain/bar compatibility.

Chainsaw Accessories

Cutting Equipment Recommendations

Approved guide bar and saw chain combinations for optimal performance and safety.

Filing Equipment & Angles

Information on file gauges and correct angles for sharpening saw chains.

Chainsaw Warranty Information

Emissions Warranty & Owner Responsibilities

Details on emissions warranty, owner's maintenance responsibility, and warranty rights.

Claims, Service & Parts

Procedures for filing claims, authorized service, and covered/non-covered parts.

Chain Saw User Safety & Kickback

Essential safety advice for chainsaw operation, focusing on kickback prevention.

Husqvarna 562XP Mark II Specifications

General

Engine Power	3.5 kW
Cylinder Displacement	59.8 cm³
Maximum Power Speed	9600 rpm
Fuel Tank Volume	0.65 l
Oil Tank Volume	0.35 l
Chain Pitch	3/8"
Weight (excl. cutting equipment)	6.1 kg
Chain gauge	0.058 in