Why does my Husqvarna Motorcycle have high oil consumption?
If your Husqvarna Motorcycle has high oil consumption, the engine vent hose might be bent; route it without bends or replace it if necessary. The engine oil level could also be too high; check it. The engine oil might also be too thin (low viscosity); change the engine oil and oil filter and clean the oil screens.
What to do if my Husqvarna 701 Supermoto Motorcycle engine dies during the journey?
If the engine of your Husqvarna Motorcycle dies during a journey, it might be due to a lack of fuel. In this case, refuel your motorcycle. Another possible cause is a blown fuse (fuse 1, 2, or 3). If this is the case, replace the blown fuse.
Why does my Husqvarna Motorcycle engine not turn when I press the starter button?
If your Husqvarna Motorcycle engine does not turn when you press the starter button, it could be due to an operating error. Make sure to follow the correct start procedure. Another cause might be a discharged battery, so recharge it and check the open-circuit current. Also, check if fuse 1 or 2 is blown and replace it if necessary. The main fuse could also be burned out, so replace it if needed. Finally, ensure there is a ground connection.
Why is the ABS warning lamp lighting up on my Husqvarna 701 Supermoto Motorcycle?
If the ABS warning lamp lights up on your Husqvarna Motorcycle, the ABS fuse may be blown; replace it. It could also be due to a large difference in wheel speeds between the front and rear wheels; in this case, stop the vehicle, switch off the ignition, and start it again. A malfunction in the ABS could also be the reason.
What causes my Husqvarna Motorcycle engine to overheat?
If your Husqvarna Motorcycle engine overheats, there might be too little coolant in the cooling system. Check the cooling system for leaks and inspect the coolant level. The radiator fins could also be very dirty; clean them if necessary. Foam formation in the cooling system can also cause overheating; in this case, drain the coolant and then fill/bleed the cooling system. A buckled or damaged radiator hose could be the problem, so replace it. The thermostat might be faulty, so check it. Finally, a blown fuse 4 can cause overheating, so replace it if necessary.
What to do if my Husqvarna 701 Supermoto engine turns but does not start?
If the engine of your Husqvarna Motorcycle turns but does not start, it could be due to an operating error; make sure to follow the correct start procedure. Another cause might be a blown fuse 3; replace it if necessary. Also, check if the plug-in connection of the fuel hose is disconnected and connect it. A defect in the fuel injection system could also be the reason.
Why is my Husqvarna 701 Supermoto battery discharged?
If the battery of your Husqvarna Motorcycle is discharged, it could be because the ignition was not switched off when the vehicle was parked; in this case, recharge the battery. Another reason could be that the battery is not being charged by the alternator; check the charging voltage and the open-circuit current.
Why are the headlight and parking light not functioning on my Husqvarna Motorcycle?
If the headlight and parking light are not functioning on your Husqvarna Motorcycle, fuse 6 might be blown; replace it.
Why are the turn signal, brake light, and horn not functioning on my Husqvarna Motorcycle?
If the turn signal, brake light, and horn are not functioning on your Husqvarna Motorcycle, fuse 5 might be blown; replace it.
Why does the combination instrument show nothing in the display on my Husqvarna 701 Supermoto?
If the combination instrument on your Husqvarna Motorcycle shows nothing in the display, fuse 1 or 2 might be blown; replace the fuses and adjust the clock.
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document for clarity.
Defines the intended use of the vehicle and its limitations.
Highlights dangers arising from using the vehicle not as intended.
General safety instructions for operating the motorcycle safely.
Explains warning symbols and their associated risk levels.
Warns against tampering with the noise control system.
Provides critical safety guidelines for operating the vehicle.
Emphasizes the importance of wearing appropriate protective gear.
Outlines rules and precautions for performing work on the vehicle.
Discusses responsible use and disposal to protect the environment.
Stresses the importance of reading and keeping the manual accessible.
Details warranty conditions and requirements for service work.
Advises on the use of specified fluids and substances for the vehicle.
Recommends using approved parts and accessories for safety.
Highlights the importance of proper service for vehicle longevity.
Notes that figures may depict special equipment and may vary.
Informs users to contact dealers for any questions.
Illustrates the front left view of the vehicle with numbered parts.
Illustrates the rear right view of the vehicle with numbered parts.
Location of the chassis number stamped on the steering head.
Indicates locations of Europe and Australia type labels on the frame.
Information on where to find the key number for ordering spare keys.
Location of the engine number stamped on the engine.
Location of the fork part number stamped on the fork stub.
Location of the shock absorber article number on the shock absorber.
Description and function of the clutch lever.
Description and function of the hand brake lever.
Description and location of the throttle grip.
Description and possible states of the horn button.
Description and possible states of the light switch.
Description and possible states of the turn signal switch.
Description and possible states of the emergency OFF switch.
Description and possible states of the electric starter button.
Description and possible states of the ignition and steering lock.
Explains the various indicator lamps on the combination instrument.
Provides an overview of the combination instrument's components.
Explains how the combination instrument is activated.
Details possible messages displayed on the instrument.
Instructions for adjusting settings on the combination instrument.
Procedure to change the unit of distance displayed.
Instructions for setting the 12h or 24h clock display.
Procedure for setting or deactivating the service interval display.
How to display and reset speed, time, and trip distance 1.
How to display and reset speed, time, and trip distance 2.
Explanation of average speed, operating hours, and total distance displays.
Essential checks and safety advice before the first ride.
Guidelines for the engine's running-in phase to ensure longevity.
Warnings and advice on vehicle handling characteristics with payload.
Pre-ride checks to ensure the vehicle is roadworthy.
Step-by-step instructions for starting the motorcycle engine.
Procedure for smoothly starting off from a standstill.
Advice on gear shifting and safe riding practices.
Guidance on proper brake application and system maintenance.
Instructions for safely stopping and parking the motorcycle.
Notes and precautions for transporting the motorcycle.
Safety precautions and procedure for refueling the vehicle.
Notes on service intervals and where to find the most up-to-date schedule.
Table detailing mandatory maintenance tasks at specific intervals.
Table outlining recommended maintenance tasks for optimal performance.
Overview of chassis tuning options for riding style and payload.
Procedure for adjusting fork compression damping.
Procedure for adjusting fork rebound damping.
Explanation of high-speed and low-speed compression damping.
Procedure for adjusting the shock absorber's low-speed compression damping.
Procedure for adjusting the shock absorber's high-speed compression damping.
Procedure for adjusting the shock absorber's rebound damping.
Steps to measure the rear wheel dimension without load.
Procedure to check and measure static sag.
Procedure to check and measure riding sag.
Instructions for adjusting the shock absorber's spring preload.
Procedure for adjusting the riding sag of the shock absorber.
Information on handlebar mounting positions for rider comfort.
Instructions for adjusting the handlebar position.
Procedure for safely lifting the motorcycle using rear lifting gear.
Steps to remove the rear of the motorcycle from its stand.
Procedure for safely lifting the motorcycle using front lifting gear.
Steps to safely lower the motorcycle from the front lifting gear.
Instructions for cleaning the fork dust boots to maintain seals.
Procedure for removing the fork protector.
Procedure for installing the fork protector.
Procedure to check for play in the steering head bearing.
Instructions for adjusting play in the steering head bearing.
Step-by-step guide to removing the motorcycle seat.
Step-by-step guide to mounting the motorcycle seat.
Procedure for removing the vehicle's tool set.
Instructions for properly storing the vehicle's tool set.
Procedure for removing the side cover panels.
Procedure for mounting the side cover panels.
Procedure for removing the front fender.
Procedure for installing the front fender.
Step-by-step guide to removing the air filter.
Step-by-step guide to installing the air filter.
Procedure to check the drive chain for dirt and soiling.
Instructions for cleaning the drive chain.
Procedure to check the drive chain tension.
Instructions for adjusting the drive chain tension.
Inspection of chain, sprockets, and guide for wear and damage.
Procedure for adjusting the chain guide based on sprocket teeth count.
Procedure to adjust the clutch lever position for rider comfort.
Procedure to check and top up hydraulic clutch fluid.
Explanation of the ABS system, its components, and warnings.
Procedure to adjust the hand brake lever position.
Instructions for checking brake disc thickness and condition.
Procedure to check the front brake fluid level.
Instructions for adding front brake fluid safely.
Procedure to check the thickness and condition of front brake linings.
Procedure to check the free travel of the foot brake lever.
Instructions for adjusting the foot brake lever position.
Procedure to check the rear brake fluid level.
Instructions for adding rear brake fluid safely.
Procedure to check the thickness and condition of rear brake linings.
Step-by-step guide for removing the front wheel.
Step-by-step guide for installing the front wheel.
Step-by-step guide for removing the rear wheel.
Step-by-step guide for installing the rear wheel.
Procedure to check rear hub rubber dampers for wear.
Guidelines for checking tire tread depth, cuts, and age.
Explanation of the vehicle's tubeless tire system advantages.
Instructions for checking and setting correct tire air pressure.
Procedure for checking spoke tension and wheel trueness.
Safety precautions and procedure for removing the battery.
Procedure for correctly installing the motorcycle battery.
Guidelines for safely recharging the vehicle battery.
Procedure for replacing the main fuse.
Procedure for replacing fuses related to the ABS system.
Procedure for replacing fuses for various electrical components.
Step-by-step guide to removing the headlight assembly.
Step-by-step guide to installing the headlight assembly.
Procedure for replacing the headlight bulb.
Procedure for replacing the parking light bulb.
Procedure to check and verify headlight alignment.
Instructions for adjusting the headlight beam range.
Location of the diagnostics connector for electronic system access.
Overview of the cooling system's operation and components.
Safety precautions and procedure for checking coolant and antifreeze.
Procedure to check coolant levels in the compensating tank and radiator.
Safety precautions and procedure for draining the cooling system.
Procedure for filling and bleeding air from the cooling system.
Safety precautions and procedure for changing the coolant.
Procedure to check the shift lever position relative to the rider's boot.
Instructions for adjusting the shift lever's basic position.
Safety precautions and procedure for changing the fuel screen.
Procedure to check the engine oil level.
Procedure for changing engine oil, filter, and cleaning oil screens.
Procedure for adding engine oil and checking for leaks.
Guidelines for washing the motorcycle safely and effectively.
Recommendations for preparing the motorcycle for winter storage.
Steps for preparing the motorcycle for long-term storage.
Procedure to ready the motorcycle after a storage period.
Possible causes and actions for engine not turning when starter is pressed.
Possible causes and actions when engine only turns with clutch lever pulled.
Possible causes and actions when engine turns but won't start.
Possible causes and actions for reduced engine power.
Possible causes and actions when the engine overheats.
Possible causes and actions for malfunction indicator lamp illumination.
Possible causes for neutral indicator lamp not lighting up.
Possible causes and actions for engine stalling during riding.
Possible causes and actions for the ABS warning lamp illumination.
Possible causes and actions for high oil consumption.
Possible causes and actions for non-functioning lights.
Possible causes for malfunctioning signals, brake, and horn.
Possible causes and actions for incorrect time display.
Possible causes and actions for a discharged battery.
Possible causes and actions for blank display on combination instrument.
Specifications related to the motorcycle's engine.
List of screws and their specified tightening torques for the engine.
Table of fluid capacities for engine oil, coolant, and fuel.
Specifications for the motorcycle's chassis components.
Specifications for the motorcycle's electrical system components.
Specifications for the front and rear tires.
Technical data for the front fork, including damping settings.
Technical data for the rear shock absorber and damping settings.
List of screws and their specified tightening torques for the chassis.
Standard classification and recommended supplier for brake fluid.
Guidelines for using high-grade coolant and antifreeze protection.
Standard classification and recommended supplier for engine oil.
Standard classification for fork oil.
Standard classification for shock absorber fluid.
Guidelines for using unleaded super fuel and ethanol content.
Recommended supplier for long-life grease.
Recommended supplier for offroad chain spray.
Recommended supplier for preserving materials.
Recommended supplier for universal oil spray.
Explanation of the JASO T903 MA standard for motorcycle engines.
Explanation of SAE viscosity classes for oils.
Definition of Anti-lock Braking System (ABS).
Definition of On-board diagnosis (OBD) system.
Indicates error conditions requiring immediate intervention.
Indicates error conditions requiring prompt intervention.
Reflects informational symbols and status indicators.
General| Displacement | 692.7 cc |
|---|---|
| Transmission | 6-speed |
| ABS | Bosch 9.1 MP (switchable) |
| Bore x Stroke | 105 mm x 80 mm |
| Compression Ratio | 12.7:1 |
| Starter | Electric |
| Final Drive | Chain |
| Front Tire | 120/70-17 |
| Rear Tire | 160/60-17 |
| Engine Type | Single cylinder, 4-stroke |
| Power | 74 hp |
| Torque | 73.5 Nm |
| Fuel System | Fuel injection |
| Fuel Tank Capacity | 13 liters |
| Seat Height | 890 mm |
| Weight | 147 kg (without fuel) |
| Front Suspension | WP APEX 48 |
| Rear Suspension | WP monoshock |
| Front Brake | Single 320 mm disc, 4-piston caliper |
| Rear Brake | Single 240 mm disc, 1-piston caliper |
| Frame | Chromium Molybdenum steel trellis |
To Next Page