What causes high oil consumption in a Husqvarna 701 Enduro 2023 Motorcycle?
High oil consumption in your Husqvarna Motorcycle can be caused by a bent engine vent hose, which should be straightened or replaced. Another cause could be an engine oil level that's too high, so check the level. Also, the engine oil might be too thin (low viscosity), requiring an oil and filter change, as well as cleaning the oil screens.
What to do if the Husqvarna 701 Enduro 2023 engine does not turn when the start button is pressed?
If the engine doesn't turn when you press the start button, it could be due to several reasons. You may not be following the correct start procedure. The 12V battery might be discharged, requiring a charge and a check of the open-circuit current. A fuse (1, 2, or 3) or the main fuse could be blown, needing replacement. Lastly, there might be no ground connection, which needs to be checked.
What to do if Husqvarna Motorcycle engine turns but does not start?
If your Husqvarna Motorcycle engine turns over but fails to start, consider these possibilities: ensure you're following the correct start procedure, check if fuse 3 is blown and replace if necessary. Make sure the quick release coupling is joined. Avoid opening the throttle while starting. If these steps don't resolve the issue, there may be a malfunction in the electronic fuel injection.
Why does the ABS warning lamp light up on my Husqvarna Motorcycle?
The ABS warning lamp might light up on your Husqvarna Motorcycle due to several reasons. The ABS fuse could be blown, requiring replacement. There might be a large difference in wheel speeds between the front and rear wheels; in this case, stop the vehicle, switch off the ignition, and start it again. Alternatively, there could be a malfunction in the ABS.
What to do if Husqvarna Motorcycle engine dies during the journey?
If your Husqvarna Motorcycle engine dies while you're riding, it could be due to a lack of fuel, so refuel your motorcycle. Another potential cause is a blown fuse (1, 2, or 3), which would need to be replaced.
Why does my Husqvarna Motorcycle engine have too little power?
If your Husqvarna Motorcycle engine has insufficient power, the air filter might be very dirty. In this case remove and install the air filter. Another potential cause is a very dirty fuel screen, which should be changed. It's also possible that the fuel filter is very dirty, so you should check the fuel pressure. Finally, there could be a malfunction in the electronic fuel injection.
Why is my Husqvarna Motorcycle engine overheating?
Your Husqvarna Motorcycle engine might be overheating for several reasons. There could be too little coolant in the cooling system, so check for leaks and the coolant level. The radiator fins might be very dirty and need cleaning. Foam formation or air in the cooling system could be the issue; in this case, drain and refill/bleed the cooling system. Other potential causes include a buckled or damaged radiator hose, a faulty thermostat, a blown fuse 4, or a defect in the radiator fan system.
Why aren't the headlight and parking light functioning on my Husqvarna 701 Enduro 2023 Motorcycle?
If the headlight and parking light on your Husqvarna Motorcycle aren't working, it's likely due to a blown fuse 6. Replace the fuse.
Why aren't the turn signal, brake light, and horn working on my Husqvarna Motorcycle?
If the turn signal, brake light, and horn on your Husqvarna Motorcycle are not functioning, the issue is likely a blown fuse 5. Replace the fuse.
What to do if the malfunction indicator lamp lights up or flashes on my Husqvarna Motorcycle?
If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates a malfunction in the electronic fuel injection.
General| Displacement | 692.7 cc |
|---|---|
| Bore x Stroke | 105 mm x 80 mm |
| Compression Ratio | 12.7:1 |
| Starter | Electric |
| Transmission | 6-speed |
| Final Drive | Chain |
| Front Suspension | WP XPLOR-USD, Ø 48 mm |
| Rear Suspension | WP XPLOR with Pro-Lever linkage |
| Ground Clearance | 270 mm |
| Front Tire | 90/90-21 |
| Rear Tire | 140/80-18 |
| Engine Type | Single-cylinder, 4-stroke |
| Power | 55 kW (74 hp) |
| Torque | 73.5 Nm |
| Fuel System | Fuel injection |
| Front Brake | Disc brake, 300 mm |
| Rear Brake | 240 mm disc, 1-piston caliper |
| ABS | Standard, disengageable |
| Seat Height | 910 mm |
| Fuel Capacity | 13 l |
| Wheelbase | 1504 mm |
| Dry Weight | 146 kg (322 lbs) |
Defines the correct intended use of the vehicle and its limitations.
Warns against improper use of the vehicle and potential dangers.
Explains danger levels and associated symbols for safety.
Identifies and locates important labels affixed to the vehicle.
Provides essential safety guidelines for operating the motorcycle.
Emphasizes the importance of wearing appropriate protective gear.
Information on maintenance, tuning, and service intervals.
Describes clutch, brake levers, throttle grip, and horn button functions.
Explains operation of light switch, turn signals, starter, and emergency stop.
Explains operation of ride modes and traction control settings.
Explains the meaning of various dashboard indicator lights.
Guides on setting display units, time, and service intervals.
How to adjust or reset the service interval reminder.
Essential checks and advice before the initial ride.
Outlines the recommended procedure for running in the new engine.
Lists essential checks before every ride for safety and roadworthiness.
Step-by-step guide on how to safely start the motorcycle.
Advice on gear shifting, handling, and safe riding practices.
Important warnings and procedures for effective and safe braking.
Guidelines for safely stopping and parking the motorcycle.
Safe procedures and guidelines for refueling the motorcycle.
Details maintenance intervals and required service tasks.
Explains the ABS system's function, operation, and warnings.
Guidance on checking and maintaining front brake fluid levels.
Detailed steps for replacing front brake pads.
Guidance on checking and maintaining rear brake fluid levels.
Detailed steps for replacing rear brake pads.
Guidelines for inspecting tire wear, damage, and tread depth.
Essential steps for checking and maintaining correct tire pressure.
Safety warnings and steps for checking coolant levels.
Detailed procedure for checking coolant level in all reservoirs.
How to correctly check the engine oil level.
Detailed steps for an oil change and filter replacement.
Steps to prepare the motorcycle for long-term storage.
A guide to diagnosing and resolving common vehicle issues.
Specifies torque values for various engine fasteners.
Details required specifications for fluids like brake fluid, coolant, and engine oil.
To Next Page