What does it mean if the malfunction indicator lamp lights up or flashes on my Husqvarna 701 Enduro?
If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, there may be a defect in the fuel injection system.
What to do if my Husqvarna Motorcycle engine does not turn when the start button is pressed?
If the Husqvarna Motorcycle engine doesn't turn when you press the start button, it could be due to several reasons. You might not be following the correct start procedure. The 12V battery could be discharged, requiring a charge and open-circuit current check. A fuse (1, 2, or 3) or the main fuse might be blown, necessitating replacement. Finally, there might be no ground connection, which needs to be checked.
Why does my Husqvarna Motorcycle engine overheat?
If your Husqvarna Motorcycle engine overheats, several factors could be the cause. There might be too little coolant, indicating a need to check for leaks and coolant level. The radiator fins could be dirty, requiring cleaning. Foam formation or air in the cooling system necessitates draining and refilling/bleeding the system. Other potential issues include a buckled or damaged radiator hose (requiring replacement), a faulty thermostat (requiring a check), a blown fuse 4 (requiring replacement), or a defect in the radiator fan system (requiring a check).
What to do if Husqvarna 701 Enduro Motorcycle engine turns but does not start?
If the Husqvarna Motorcycle engine turns but doesn't start, several issues could be at play. You may not be following the correct start procedure. Fuse 3 could be blown, requiring replacement. The quick release coupling might not be joined, so ensure it is connected. There could be a malfunction in the electronic fuel injection, requiring a diagnostic tool. Also, avoid opening the throttle while starting, and ensure you follow the correct start procedure.
Why does my Husqvarna 701 Enduro engine have too little power?
If your Husqvarna Motorcycle engine has too little power, the air filter might be very dirty, requiring removal and installation. The fuel screen could be very dirty, needing replacement. The fuel filter might be dirty, so check the fuel pressure. Also, there could be a malfunction in the electronic fuel injection, requiring a diagnostic tool.
Why is my Husqvarna 701 Enduro battery discharged?
If the battery of your Husqvarna Motorcycle is discharged, it could be because the ignition was not switched off when the vehicle was parked; in this case, recharge the battery. Another reason could be that the battery is not being charged by the alternator; check the charging voltage and the open-circuit current.
What causes my Husqvarna 701 Enduro engine to overheat?
If your Husqvarna Motorcycle engine overheats, there might be too little coolant in the cooling system. Check the cooling system for leaks and inspect the coolant level. The radiator fins could also be very dirty; clean them if necessary. Foam formation in the cooling system can also cause overheating; in this case, drain the coolant and then fill/bleed the cooling system. A buckled or damaged radiator hose could be the problem, so replace it. The thermostat might be faulty, so check it. Finally, a blown fuse 4 can cause overheating, so replace it if necessary.
What to do if my Husqvarna 701 Enduro Motorcycle engine turns but does not start?
If the engine of your Husqvarna Motorcycle turns but does not start, it could be due to an operating error; make sure to follow the correct start procedure. Another cause might be a blown fuse 3; replace it if necessary. Also, check if the plug-in connection of the fuel hose is disconnected and connect it. A defect in the fuel injection system could also be the reason.
Why are the headlight and parking light not functioning on my Husqvarna 701 Enduro?
If the headlight and parking light are not functioning on your Husqvarna Motorcycle, fuse 6 might be blown, requiring replacement.
Why does my Husqvarna Motorcycle engine turn only if the clutch lever is drawn?
If the Husqvarna Motorcycle engine turns only when the clutch lever is drawn, the vehicle is likely in gear. Shift the transmission to neutral position. This issue can also occur if the vehicle is in gear and the side stand is folded out, so shift to neutral.
Explains the meaning of various symbols used in the manual for clear understanding.
Details typographical formats like proprietary names and underlined terms for document clarity.
Defines the vehicle's intended purpose and limitations, such as suitability for gentle terrain.
Explains danger, warning, caution, and note symbols to ensure user safety and understanding of risks.
Warns against modifying the noise control system and lists acts considered tampering.
Provides critical safety instructions for operating the motorcycle, covering rider fitness and environmental hazards.
Emphasizes the importance of wearing appropriate protective gear for rider safety.
Outlines general rules and precautions to be followed when performing work on the vehicle.
Stresses the importance of reading the manual for operating, handling, and servicing the motorcycle.
Illustrates and labels key components of the vehicle from the front left perspective.
Illustrates and labels key components of the vehicle from the rear right perspective.
Details the location and importance of the Vehicle Identification Number (VIN).
Explains the location of type labels for different regions (Europe and Australia).
Informs about finding the key number on the KEYCODECARD for ordering spare keys.
Specifies the location where the engine number is stamped on the engine.
Indicates the location of the fork part number stamp on the fork stub.
Identifies the location of the shock absorber article number.
Describes the clutch lever's location, hydraulic activation, and automatic adjustment.
Explains the location and function of the hand brake lever, which operates the front brake.
Details the location of the throttle grip on the handlebar.
Describes the location and operation of the horn button.
Explains the location and operation of the light switch for low and high beams.
Details the location and operation of the turn signal switch for activating signals.
Describes the location and function of the emergency OFF switch for interrupting ignition.
Explains the location and operation of the start button for actuating the starter motor.
Identifies the location of the ABS button, also used as the ABS warning lamp.
Explains the function and possible states of the combination switch for mode selection.
Details the location and states of the ignition and steering lock.
Explains the meaning and function of various indicator lights on the dashboard.
Describes how to unlock the seat using the designated loop.
Explains the purpose of grab handles for moving the motorcycle and for passenger use.
Details the foldable nature of passenger foot pegs for use with or without a passenger.
Identifies the location of the shift lever on the engine.
Locates the foot brake lever and explains its function for engaging the rear brake.
Explains the location and use of the side stand for parking and its relation to the starting system.
Provides detailed instructions and safety warnings for opening the fuel tank filler cap.
Outlines the procedure for properly closing the fuel tank filler cap.
Provides an overview and labels of the components on the vehicle's dashboard display.
Explains how the combination instrument activates and performs a display test.
Guides on how to customize the combination instrument display settings.
Explains how to change the unit of distance measurement between kilometers and miles.
Provides instructions on setting the clock on the combination instrument.
Details how to set or reset the service interval indicator on the display.
Explains the function and reset procedure for the Trip meter 1.
Explains the function and reset procedure for the Trip meter 2.
Details how to view and reset the average speed 1 display.
Details how to view and reset the average speed 2 display.
Explains how to view and reset the riding time 1 display.
Explains how to view and reset the riding time 2 display.
Details the function of the service hour counter.
Explains how to view the current time on the display.
Explains how to view the remaining distance or time until the next service is due.
Details how to view engine speed (RPM) and provides a guideline for reading values.
Explains how to view the motorcycle's overall mileage.
Explains the function of the gear display, showing the currently engaged gear.
Explains when the service display appears, indicating that service is due.
Explains the indicator showing distance traveled since the fuel reserve was reached.
Provides essential advice and warnings before the first use of the motorcycle.
Details the procedure and guidelines for the engine's break-in period to ensure longevity.
Offers warnings and advice on safely loading the vehicle with luggage.
Lists essential checks and maintenance tasks to ensure the vehicle is roadworthy before each trip.
Provides step-by-step instructions and safety precautions for starting the motorcycle's engine.
Explains the procedure for safely setting off from a standstill.
Offers guidance on proper shifting techniques and safe riding practices.
Describes the Easy Shift system, allowing clutchless up and down shifts.
Explains the function of the motorcycle traction control (MTC) and how to activate/deactivate it.
Provides critical safety warnings and instructions related to braking.
Details safe procedures for stopping and parking the motorcycle, including security measures.
Offers guidance and safety notes for transporting the motorcycle.
Provides essential safety information and instructions for refueling the vehicle.
Provides general information regarding service intervals and their applicability.
Lists mandatory maintenance tasks and their recommended intervals.
Outlines recommended maintenance tasks for optimal vehicle performance and longevity.
Introduces the suspension system and options for adapting it to riding style and load.
Explains how to adjust the fork's compression damping for different riding conditions.
Details the procedure for adjusting the fork's rebound damping for optimal suspension behavior.
Explains the concept of high-speed and low-speed compression damping for the shock absorber.
Guides on how to adjust the low-speed compression damping of the shock absorber.
Explains how to adjust the high-speed compression damping of the shock absorber.
Details the procedure for adjusting the shock absorber's rebound damping.
Describes how to adjust the handlebar position for rider comfort.
Provides instructions on adjusting the handlebar's mounting position.
Explains the procedure for safely lifting the motorcycle using a stand.
Details the steps for safely removing the motorcycle from a lift stand.
Guides on how to raise the motorcycle using rear lifting equipment.
Explains how to safely remove the rear section of the motorcycle from lifting gear.
Provides instructions for cleaning the dust boots on the fork legs.
Details the process for removing the fork protector.
Guides on how to install the fork protector.
Explains the procedure for bleeding the fork legs.
Details how to remove the motorcycle seat.
Provides instructions for correctly mounting the motorcycle seat.
Explains how to remove the tool set from its compartment.
Guides on how to properly store the tool set.
Provides steps for removing the side cover.
Guides on how to install the side cover.
Details the procedure for removing the front fender.
Provides instructions for installing the front fender.
Explains how to remove the air filter.
Guides on how to properly install the air filter.
Details how to check the chain for dirt and soiling.
Provides instructions for cleaning the motorcycle chain.
Explains how to check the chain tension and the consequences of incorrect tension.
Guides on how to adjust the chain tension correctly.
Outlines how to check wear on the chain, sprockets, and chain guide.
Details how to adjust the chain guide based on sprocket tooth count.
Explains how to adjust the clutch lever's position for rider comfort.
Guides on checking and correcting the hydraulic clutch fluid level.
Details the procedure for removing the engine guard.
Provides instructions for installing the engine guard.
Explains the ABS system, its components, and warnings regarding changes to the vehicle.
Guides on adjusting the hand brake lever's position for rider comfort.
Details how to check the brake discs for wear and damage.
Explains how to check the front brake fluid level and warnings about insufficient fluid.
Provides instructions and safety warnings for adding front brake fluid.
Details how to check the front brake linings for wear.
Provides instructions and safety warnings for changing the front brake linings.
Explains how to check the free travel of the foot brake lever.
Guides on adjusting the foot brake lever's position.
Details how to check the rear brake fluid level and related warnings.
Provides instructions and safety warnings for adding rear brake fluid.
Details how to check the rear brake linings for wear.
Provides instructions and safety warnings for changing the rear brake linings.
Details the procedure for removing the front wheel.
Guides on how to properly install the front wheel.
Provides instructions for removing the rear wheel.
Guides on how to properly install the rear wheel.
Explains how to check the rear hub damping rubber pieces for wear.
Details how to check the tire for cuts, damage, and tread depth.
Provides guidelines for checking and maintaining correct tire pressure.
Explains how to check spoke tension and the importance of regular checks.
Offers instructions and warnings about using tire repair spray in emergencies.
Provides instructions and safety warnings for removing the 12-V battery.
Guides on how to properly install the 12-V battery.
Details the procedure and precautions for charging the 12-V battery.
Explains how to change the main fuse and the importance of correct ampere value.
Guides on how to change the fuses related to the ABS system.
Details how to change fuses for various electrical components.
Provides instructions for removing the headlight mask and headlight assembly.
Guides on how to reinstall the headlight mask and headlight assembly.
Explains how to replace the headlight bulb, including precautions.
Details how to replace the position light bulb.
Provides instructions on how to check and verify the correct headlight beam setting.
Guides on how to adjust the headlight beam range.
Explains the location and purpose of ACC1 and ACC2 power supply connections.
Identifies the location of the diagnostics connector for system checks.
Explains the basic operation of the cooling system, including the water pump and coolant circulation.
Provides instructions and safety warnings for checking coolant and antifreeze levels.
Details how to check the coolant level in the compensating tank and radiator.
Explains the procedure for draining the coolant, including safety precautions.
Guides on how to refill and bleed the cooling system.
Provides instructions for changing the coolant, including safety warnings.
Explains how to select different riding modes (Street, Sport) via the MAP button.
Details how to activate and deactivate the traction control system using the TC button.
Explains how to check the basic position of the shift lever relative to the rider's boot.
Guides on how to adjust the basic position of the shift lever.
Provides instructions and safety warnings for changing the fuel screen.
Details how to check the engine oil level and the importance of correct oil levels.
Guides on changing engine oil, oil filter, and cleaning oil screens.
Provides instructions and safety warnings for adding engine oil.
Offers guidelines and warnings for cleaning the motorcycle using a pressure cleaner or other methods.
Lists checks and maintenance steps specifically for preparing the motorcycle for winter operation.
Provides steps for properly storing the motorcycle for extended periods.
Details the necessary steps to take the motorcycle out of storage and prepare it for riding.
Lists detailed technical specifications for the motorcycle's engine.
Provides a table of critical tightening torques for various engine screws and bolts.
Lists the required capacities for engine oil, coolant, and fuel.
Details technical specifications related to the motorcycle's chassis, suspension, and brakes.
Lists technical data for the 12-V battery and fuses.
Specifies the front and rear tire models used as series production tires.
Provides technical data for the fork, including damping and spring rates.
Lists technical data for the shock absorber, including damping adjustments.
Provides a table of chassis-related tightening torques for screws and nuts.
Details the standard classification and recommended suppliers for brake fluid.
Provides guidelines for using high-grade, silicate-free coolant and its antifreeze protection.
Specifies the standard and recommended suppliers for engine oil.
Details standards and guidelines for fork oil.
Specifies standards and guidelines for shock absorber fluid.
Details standards and guidelines for super unleaded fuel, including ethanol content.
Recommends MOTOREX® Chain Clean for cleaning the chain.
Recommends MOTOREX® Fuel Stabilizer for fuel stability.
Recommends MOTOREX® Bike Grease 2000 for long-life lubrication.
Recommends MOTOREX® Moto Clean for cleaning the motorcycle.
Recommends MOTOREX® Moto Shine for paint care.
Recommends MOTOREX® Moto Protect for preserving materials.
Recommends MOTOREX® Silicone Spray.
Recommends MOTOREX® Quick Cleaner for surface cleaning.
Recommends MOTOREX® Chainlube Road Strong for chain lubrication.
Recommends MOTOREX® Joker 440 Synthetic for universal oil spray.
Explains the JASO T903 MA2 standard for motorcycle engine oils.
Explains the SAE classification system for oil viscosity.
Explains red symbols indicating error conditions requiring immediate intervention.
Explains yellow/orange symbols indicating error conditions requiring prompt intervention.
Explains green and blue symbols that reflect information.
Defines ABS as Anti-lock braking system and its function.
Defines Easy Shift as an engine electronics function for clutchless shifting.
Defines MTC as Motorcycle Traction Control, an auxiliary function for reducing engine torque.
Defines OBD as On-board diagnosis for monitoring vehicle electronics.
General| Engine Type | Single cylinder, 4-stroke |
|---|---|
| Displacement | 692.7 cc |
| Transmission | 6-speed |
| Rear Suspension | WP XPLOR with Pro-Lever linkage |
| Bore x Stroke | 105 mm x 80 mm |
| Lubrication | Forced oil lubrication with 2 oil pumps |
| Cooling | Liquid cooled |
| Frame | Chromium-Molybdenum steel trellis frame |
| Front Tire | 90/90-21 |
| Rear Tire | 140/80-18 |
| Compression Ratio | 12.7:1 |
| Starter | Electric |
| Final Drive | Chain |
| Power | 55 kW (74 hp) |
| Torque | 73.5 Nm |
| Fuel Capacity | 13 liters |
| Front Suspension | WP XPLOR |
| Fuel System | Keihin EFI with 50 mm throttle body |
| Clutch | APTCTM slipper clutch, hydraulically actuated |
| Front Brake | Disc brake |
| Rear Brake | Disc brake |
| ABS | Bosch 9.1 MP |
| Wheelbase | 1, 502 mm |
| Dry Weight | 146 kg |
| Front Suspension Travel | 250 mm |
| Rear Suspension Travel | 250 mm |
| Front Brake Details | 300 mm disc |
| Rear Brake Details | 240 mm disc |
| Ground Clearance | 270 mm |
To Next Page