What to do if Husqvarna EE 5 2022 shows blink code 88?
If you are experiencing blink code 88 on your Husqvarna Motorcycle, it indicates a malfunction in the On/Off button. First, try deactivating the vehicle, waiting four minutes, and then reactivating it. If the issue persists, inspect the On/Off button for any signs of damage.
How to fix blink code 73 on a Husqvarna EE 5 2022?
If your Husqvarna Motorcycle is showing blink code 73, it means there's a malfunction during charging. Here's what you should do: * Disconnect the battery charger from both the vehicle and the mains connection. * Wait for one minute. * Restart the charging process. If the problem continues, replace the charging cable.
What to do if Husqvarna EE 5 2022 Motorcycle shows blink code 85?
Blink code 85 on your Husqvarna Motorcycle indicates a malfunction during charging. To resolve this, disconnect the battery charger from the vehicle and the mains connection. Wait for one minute, then restart the charging process. If the problem persists, try replacing the charging cable.
General| Model Year | 2022 |
|---|---|
| Engine Type | Electric |
| Battery Voltage | 48 V |
| Category | Electric Motorcycle |
| Engine | Permanent magnet electric motor |
| Power | 11 kW (15 hp) |
| Charging Time 100% | 70 minutes |
| Front Suspension | WP XACT 35 |
| Rear Suspension | WP XACT |
| Suspension Front | WP Xplor 43 mm upside-down fork |
| Suspension Rear | WP Xplor PDS shock absorber |
| Front Brake | Hydraulic disc brake |
| Rear Brake | Hydraulic disc brake |
| Brakes Front | 260 mm disc, 2-piston caliper |
| Brakes Rear | 220 mm disc, 1-piston caliper |
Explains the meaning of various symbols used in the manual for guidance.
Details the typographical formats used for clarity and consistency.
Defines the intended purpose and usage of the motorcycle for safe operation.
Categorizes potential dangers and their severity to inform users of risks.
Provides essential guidelines for operating the vehicle safely.
Emphasizes the necessity of appropriate protective gear for riders.
Stresses the importance of proper service for optimal operation and longevity.
Illustrates and identifies key components from the front left view of the motorcycle.
Illustrates and identifies key components from the rear right view of the motorcycle.
Details the location of the VIN for vehicle identification purposes.
Specifies the location of the motor number for identification.
Indicates the location of the battery identification number (BIN).
Describes the hand brake lever and its function for controlling the front brake.
Explains the operation of the throttle grip for controlling speed.
Explains the function of the magnetic switch under the seat for ride mode control.
Explains the different ride modes and how they are visually displayed.
Details the charging level indicator and its various states.
Offers crucial advice and safety warnings for the initial use of the vehicle.
Lists essential checks and maintenance before operating the vehicle.
Instructs on proper brake application techniques for safe stopping.
Details the correct procedure for safely stopping and parking the motorcycle.
Lists mandatory maintenance tasks to be performed at specified intervals.
Lists optional but recommended maintenance tasks for optimal performance.
Guides on adjusting the chassis setting based on rider weight for optimal performance.
Explains how to adjust the low-speed compression damping of the shock absorber.
Explains how to adjust the high-speed compression damping of the shock absorber.
Details how to check the static sag of the shock absorber for proper setup.
Provides instructions for adjusting the fork's air pressure for suspension tuning.
Outlines the different methods available for adjusting the seat height.
Explains the process of adjusting the seat height by modifying the fork position.
Details the procedure for removing the motorcycle's fork legs for maintenance or repair.
Guides on the process of installing the lower triple clamp correctly.
Explains how to check for and identify play in the steering head bearing.
Provides instructions for cleaning the motorcycle's drive chain properly.
Details how to check and adjust the chain tension for optimal performance.
Describes how to check the free play of the handbrake lever.
Explains how to check the front brake fluid level to ensure system functionality.
Outlines the procedure for changing the front brake linings.
Details how to check the rear brake linings for wear and damage.
Guides on the process of removing the front wheel for maintenance or replacement.
Details the procedure for removing the rear wheel for maintenance or replacement.
Explains how to check and set the correct tire pressure for optimal riding.
Provides guidance on safely positioning the battery charger for optimal operation.
Details the procedure for safely and correctly charging the Powerpack LV.
Provides instructions for cleaning the motorcycle safely and effectively to maintain its condition.
Lists technical specifications for the motorcycle's engine.
Provides technical specifications related to the motorcycle's chassis components.
Lists specific torque values required for tightening various chassis components.
Explains the meaning of yellow and orange symbols indicating errors or warnings.
To Next Page