What to do if the FI warning lamp (MIL) lights up/flashes on my Husqvarna Motorcycle?
If the FI warning lamp lights up or flashes on your Husqvarna Motorcycle, stop the motorcycle. Identify the faulty part using the blink code. Check the cabling for damage and the electrical plug-in connections for corrosion and damage. You can also read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
Why does my Husqvarna Motorcycle engine overheat?
Your Husqvarna Motorcycle engine may be overheating due to several reasons: * Too little coolant in the cooling system. Check for leakage and the coolant level. * Too little air stream. Switch off the engine when standing. * Radiator fins very dirty. Clean the radiator fins. * Foam formation in the cooling system. Drain and refill the coolant. * Bent radiator hose. Change the radiator hose.
What to do if my Husqvarna Motorcycle engine does not turn when pressing the electric starter button?
If your Husqvarna Motorcycle engine doesn't turn when you press the electric starter, it could be due to several reasons: * Operating error: Carry out the start procedure. * Battery discharged: Recharge the battery and check the charging voltage, open-circuit current, and the stator winding of the alternator. * Main fuse blown: Change the main fuse. * Faulty starter relay: Check the starter relay. * Faulty starter motor: Check the starter motor.
Why does my Husqvarna Motorcycle have high oil consumption?
High oil consumption in your Husqvarna Motorcycle can be caused by: * A bent engine vent hose. Route the vent hose without bends or replace it. * Engine oil level too high. Check the engine oil level. * Engine oil too thin (low viscosity). Change the engine oil and oil filter, and clean the oil screen. * Worn piston or cylinder. Measure the piston/cylinder mounting clearance. * Battery is not charging. Check the charging voltage and the stator winding of the alternator. * Unwanted power consumer. Check the open-circuit current.
What to do if my Husqvarna Motorcycle engine turns but does not start?
If your Husqvarna Motorcycle engine turns but doesn't start, consider these possible causes: * The plug-in connection of the fuel line is not connected. Connect the plug-in connection of the fuel line. * Fuel screen in the fuel hose connection is clogged. Change the fuel screen. * Idle speed is not set correctly. Adjust the idle speed. * Spark plug oily or wet. Clean and dry the spark plug, or change it if necessary. * Electrode distance (plug gap) of spark plug too wide. Adjust the plug gap to 0.8 mm (0.031 in). * Short circuit cable in wiring harness frayed, kill switch defective. Check the wiring harness (visual check) and the electrical system. * Defect in fuel injection system. Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
What causes a Husqvarna Motorcycle engine to have too little power?
If your Husqvarna Motorcycle engine has too little power, it could be due to: * A very dirty air filter. Clean the air filter and air filter box. * A very dirty fuel filter. Change the fuel filter. * A defect in the fuel injection system. Read out the fault memory using the Husqvarna Motorcycles diagnostics tool. * A leaky or deformed exhaust system, or too little glass fiber yarn filling in the main silencer. Check the exhaust system for damage and change the glass fiber yarn filling of the main silencer. * Valve clearance too little. Adjust the valve clearance.
What to do if my Husqvarna Motorcycle engine does not speed up?
If your Husqvarna Motorcycle engine does not speed up, the issue might be a defect in the fuel injection system. Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
General safety instructions, risk degrees, and safe operation guidelines.
Details warranty, fluids, parts, service, and customer support information.
Explains the location of chassis, engine, fork, and shock absorber numbers.
Description of clutch, brake levers, throttle, kill switch, and starter button.
Advice for first use, engine break-in, battery, and preparing for conditions.
Essential checks before operation and engine starting procedure.
Guidance on starting off, shifting, riding, and applying brakes.
Lists periodic maintenance tasks at different operating hour intervals.
Steps for servicing chassis components like forks, steering, and frame.
Procedures for checking and maintaining brake fluid, linings, and discs.
Procedures for battery maintenance, charging, and fuse replacement.
Procedures for changing fuel screen, engine oil, and adding oil.
Adjusting chassis settings like suspension, sag, and damping.
Adjusting throttle response, idle speed, and engine mapping.
Detailed specifications for engine, chassis, and related components.
Solutions for common engine, starting, and operational problems.
General| Engine Type | Single-cylinder, 4-stroke |
|---|---|
| Bore x Stroke | 78 mm x 52.3 mm |
| Compression Ratio | 14.4:1 |
| Transmission | 5-speed |
| Seat Height | 950 mm |
| Starter | Electric |
| Fuel System | Electronic fuel injection (EFI) |
| Fuel Tank Capacity | 7 L |
| Front Suspension | WP USD, 48 mm |
| Rear Suspension | WP monoshock |
| Front Brake | Disc brake |
| Rear Brake | Brembo, single disc |
| Frame | Chromium Molybdenum steel |
| Ground Clearance | 370 mm |
| Displacement | 249.9 cc |
To Next Page
