Husqvarna TC 250 2017

Questions and Answers

B
Brenda WrightAug 18, 2025
What to do if Husqvarna TC 250 2017 engine cannot be cranked (electric starter) (TX 300)?
- A
  Austin LewisAug 18, 2025
  If your Husqvarna TX 300 Motorcycle engine fails to crank with the electric starter, first ensure you are following the correct start procedure. If that's not the issue, check the battery. It may need recharging, or the charging voltage, closed current, or alternator might need inspection. Also, inspect the main fuse and replace it if it's blown. The starter relay or starter motor could be faulty and require checking.
W
wwilkersonAug 21, 2025
Why does my Husqvarna TC 250 2017 engine overheat?
- J
  Jesse WoodAug 22, 2025
  Your Husqvarna Motorcycle engine may overheat due to several reasons. Check if there is enough coolant in the cooling system and inspect for any leaks. Ensure there's sufficient air stream, and switch off the engine when stationary. Clean the radiator fins if they are very dirty. Foam formation in the cooling system may also cause overheating, so drain and refill the coolant. Damaged cylinder head or cylinder head gasket, a bent radiator hose, or an incorrect ignition point due to a loose stator can also lead to overheating. Check and correct these issues accordingly.
B
butlerjohnAug 26, 2025
What to do if Husqvarna TC 250 2017 engine does not speed up?
- J
  Jesse SchwartzAug 26, 2025
  If your Husqvarna Motorcycle engine isn't speeding up, several factors could be responsible. Start by checking the carburetor components, as the carburetor might be running over due to a dirty or worn float needle, or the jets might be loose. Inspect the ignition system for any faults. Ensure there's proper fuel feed by checking the fuel tank breather and cleaning the fuel tap. A very dirty air filter can restrict airflow, so clean the air filter and air filter box. Also, examine the exhaust system for leaks or deformation, and replace the glass fiber yarn filling in the main silencer if it's insufficient.
A
Autumn LawrenceAug 28, 2025
Why Husqvarna TC 250 2017 engine stalls or is popping into the carburetor?
- J
  James MendezAug 28, 2025
  If your Husqvarna Motorcycle engine stalls or pops into the carburetor, it could be due to a lack of fuel. Ensure the fuel tap is in the ON position (or RES position for TX 300) and refuel if necessary. Another cause might be the engine taking in bad air, so check the intake flange and carburetor for tightness. Also, inspect the connector or ignition coil for looseness or oxidation; clean the connector and treat it with contact spray if needed.
K
Kimberly SpencerAug 31, 2025
How to fix Husqvarna TC 250 2017 Motorcycle engine that has no idle?
- A
  Austin MejiaSep 1, 2025
  If your Husqvarna Motorcycle engine has no idle, the idling jet might be blocked, so check/set the carburetor components. The adjusting screws on the carburetor could be distorted, so adjust the idle speed. A defective spark plug or ignition system can also cause this issue; change the spark plug and check the ignition coil and spark plug connector.
J
Joseph JacobsSep 4, 2025
Why is gear oil exiting at the vent hose of my Husqvarna Motorcycle?
- C
  courtney22Sep 4, 2025
  If gear oil is exiting at the vent hose of your Husqvarna Motorcycle, it's likely because too much gear oil was added. Check the gear oil level.
B
brianmooreSep 8, 2025
What causes white smoke emission (steam in exhaust gas) in Husqvarna TC 250 2017?
- J
  Jessica WalkerSep 8, 2025
  White smoke emission (steam in exhaust gas) in your Husqvarna Motorcycle is caused by a damaged cylinder head or cylinder head gasket. In this case, check the cylinder head and cylinder head gasket.
C
cynthia16Sep 12, 2025
What causes water in the gear oil of my Husqvarna TC 250 2017?
- V
  Victoria ProctorSep 12, 2025
  Water in the gear oil of your Husqvarna Motorcycle can be caused by a damaged shaft seal ring or water pump. Check these components for damage.
J
juliamorrisNov 14, 2025
Why does my Husqvarna TC 250 2017 Motorcycle engine turn but not start?
- P
  Patricia HarrisonNov 14, 2025
  Several factors can prevent your Husqvarna Motorcycle engine from starting even when it turns. It could be due to an operating error, so ensure you follow the correct start procedure. If the motorcycle has been out of use for a while, old fuel in the float chamber might be the issue; in this case, empty the carburetor float chamber. Also, check for fuel feed interruptions by inspecting the fuel tank breather and cleaning the fuel tap. A spark plug that's oily or wet should be cleaned, dried, or replaced. Make sure the spark plug electrode distance (plug gap) is correctly adjusted to 0.60 mm (0.0236 in). Other potential causes include a fault in the ignition system, a frayed or defective kill switch cable, a loose or oxidized connector or ignition coil (clean the connector and treat it with...

Summary

SAFETY ADVICE

Use definition - intended use

Safety advice

General safety instructions for operating the vehicle.

Degrees of risk and symbols

Explains danger, warning, and caution symbols.

Safe operation

Provides crucial safety guidelines for operating the motorcycle.

Protective clothing

Emphasizes the importance of wearing appropriate protective gear.

PREPARING FOR USE

Advice on first use

Crucial advice for initial use, including safety and controls.

Running in the engine

Preparing the vehicle for difficult riding conditions

RIDING INSTRUCTIONS

Checks and maintenance work when preparing for use

Lists essential pre-ride checks for safety and operation.

Starting

Provides instructions and warnings for starting the engine.

Starting off

Shifting, riding

Braking

Details proper braking techniques and warnings.

Stopping, parking

Refueling

Provides instructions and safety warnings for refueling the motorcycle.

SERVICE SCHEDULE

All TC models

TX 300

TUNING THE CHASSIS

Checking the basic chassis setting with the riders weight

Air suspension AER 48

Compression damping of the shock absorber

Adjusting the low-speed compression damping of the shock absorber

Guides on adjusting low-speed compression damping.

Adjusting the high-speed compression damping of the shock absorber

Guides on adjusting high-speed compression damping.

Adjusting the rebound damping of the shock absorber

Guides on adjusting rebound damping of the shock absorber.

Checking the static sag of the shock absorber

Checking the riding sag of the shock absorber

Adjusting the spring preload of the shock absorber

Guides on adjusting the shock absorber spring preload.

Adjusting the riding sag

Guides on adjusting the riding sag of the shock absorber.

Checking the basic setting of the fork

Adjusting the fork air pressure

Guides on adjusting the air pressure in the fork.

Adjusting the compression damping of the fork

Guides on adjusting fork compression damping.

Adjusting the rebound damping of the fork

Guides on adjusting fork rebound damping.

Adjusting the handlebar position

SERVICE WORK ON THE CHASSIS

Raising the motorcycle with a lift stand

Removing the motorcycle from the lift stand

Bleeding the fork legs

Instructions for bleeding the fork legs.

Removing the fork legs

Provides steps for removing the fork legs.

Installing the fork legs

Guides on correctly installing the fork legs.

Removing the lower triple clamp

Installing the lower triple clamp

Checking the play of the steering head bearing

Explains how to check for play in the steering head bearing.

Adjusting the steering head bearing play

Guides on adjusting steering head bearing play.

Removing the shock absorber

Provides steps for removing the shock absorber.

Installing the shock absorber

Guides on correctly installing the shock absorber.

Removing the air filter

Cleaning the air filter and air filter box

Guides on cleaning the air filter and its housing.

Removing the main silencer

Installing the main silencer

Removing the fuel tank

Instructions and safety warnings for removing the fuel tank.

Installing the fuel tank

Guides on correctly installing the fuel tank.

Cleaning the chain

Checking the chain tension

Explains how to check and set the drive chain tension.

Checking the chain, rear sprocket, engine sprocket, and chain guide

Checking the frame

Checking the swingarm

Adjusting the basic position of the clutch lever

Checking;correcting the fluid level of the hydraulic clutch

How to check and correct the hydraulic clutch fluid level.

Changing the hydraulic clutch fluid

Instructions for changing the hydraulic clutch fluid.

BRAKE SYSTEM

Checking the free travel of the hand brake lever

Adjusting the basic position of the hand brake lever

Checking the brake discs

How to check the thickness and condition of brake discs.

Checking the front brake fluid level

How to check the front brake fluid level.

Adding front brake fluid

Instructions for adding front brake fluid.

Checking the front brake linings

How to check the minimum thickness of front brake linings.

Changing the front brake linings

Instructions for changing the front brake linings.

Checking the free travel of foot brake lever

Adjusting the basic position of the foot brake lever

Checking the rear brake fluid level

How to check the rear brake fluid level.

Adding rear brake fluid

Instructions for adding rear brake fluid.

Checking the rear brake linings

How to check the minimum thickness of rear brake linings.

Changing the rear brake linings

Instructions for changing the rear brake linings.

WHEELS, TIRES

Removing the front wheel

Steps for safely removing the front wheel.

Installing the front wheel

Guides on correctly installing the front wheel.

Removing the rear wheel

Steps for safely removing the rear wheel.

Installing the rear wheel

Guides on correctly installing the rear wheel.

Checking the tire condition

Checking the tire air pressure

How to check and adjust tire air pressure for off-road use.

ELECTRICAL SYSTEM

Removing the battery (TX 300)

Installing the battery (TX 300)

Recharging the battery (TX 300)

Changing the main fuse (TX 300)

COOLING SYSTEM

Checking the antifreeze and coolant level

Checking the coolant level

Draining the coolant

Refilling with coolant

TUNING THE ENGINE

Checking the play in the throttle cable

Adjusting the play in the throttle cable

Carburetor setting

Carburetor - idle

Carburetor - adjusting the idle speed

Changing the ignition timing map

Adjusting the basic position of the shift lever

Engine characteristic - setting the auxiliary spring (TC 250, TX 300)

SERVICE WORK ON THE ENGINE

Checking the gear oil level

Changing the gear oil

Adding gear oil

CLEANING, CARE

Cleaning the motorcycle

STORAGE

Storage

Preparing for use after storage

TROUBLESHOOTING

The engine cannot be cranked (electric starter) (TX 300)

Troubleshooting steps for when the engine won't crank.

Engine turns but does not start

Troubleshooting steps when the engine cranks but doesn't start.

Engine has no idle

Engine does not speed up

Engine has too little power

Engine stalls or is popping into the carburetor

Engine overheats

Troubleshooting steps for engine overheating issues.

TECHNICAL DATA

Engine

Engine tightening torques

Table of tightening torques for engine components.

Carburetor

Capacities

Chassis

Chassis tightening torques

Table of tightening torques for chassis components.

SUBSTANCES

Brake fluid DOT 4

Coolant

Engine oil (SAE 10 W;40)

Engine oil, 2-stroke

Fork oil (SAE 4) (48601166 S1)

Husqvarna TC 250 2017 Specifications

General

Displacement	249 cc
Transmission	6-speed
Rear Suspension	WP mono shock
Front Tire	80/100-21
Starter	Kick starter
Bore x Stroke	66.4 mm x 72 mm
Clutch	Wet, multi-disc
Frame	Chromium-molybdenum steel
Front Suspension	WP AER 48, USD fork
Front Brake	260 mm disc
Rear Tire	110/90-19
Wheelbase	1, 485 mm
Seat Height	960 mm
Fuel Tank Capacity	7.5 liters