Husqvarna FC 250 2022 User Manual

OWNER'S MANUAL 2022
FC 250
Art. no. 3402532en

Husqvarna FC 250 2022 Specifications

General

Engine Type	Single-cylinder, 4-stroke
Displacement	249.9 cc
Bore x Stroke	78 mm x 52.3 mm
Compression Ratio	14.4:1
Starter	Electric
Transmission	5-speed
Front Suspension	WP XACT-USD, Ø 48 mm
Ground Clearance	370 mm
Fuel System	Fuel injection
Clutch	Wet multi-disc
Frame	Chromium Molybdenum Steel
Rear Suspension	WP XACT Monoshock
Front Brake	Disc brake
Rear Brake	Disc brake
Front Wheel	21 inch
Rear Wheel	19 inch
Wheelbase	1485 mm

Summary

Safety Advice

Use Definition – Intended Use

Defines the intended use of the vehicle and its restrictions.

Misuse

Describes potential dangers arising from unintended use of the vehicle.

Safety Advice

Highlights the importance of following safety instructions and warning labels.

Degrees of Risk and Symbols

Explains the meaning of danger, warning, caution, and note symbols.

Tampering Warning

Warns against tampering with the noise control system and lists prohibited acts.

Safe Operation

Provides critical safety information for operating the vehicle.

Protective Clothing

Emphasizes the importance of wearing appropriate protective clothing.

Important Notes

Serial Numbers

Vehicle Identification Number

Shows where the Vehicle Identification Number is stamped on the steering head.

Type Label

Indicates the location of the vehicle's type label on the steering head.

Engine Number

Shows the location of the engine number on the engine case.

Fork Article Number

Indicates where the fork article number is stamped on the axle clamp.

Shock Absorber Article Number

Shows the location of the shock absorber article number.

Controls

Clutch Lever

Describes the clutch lever and its operation.

Hand Brake Lever

Identifies the hand brake lever and its function.

Throttle Grip

Describes the throttle grip and its location.

Stop Button

Explains the function and states of the stop button.

Start Button

Explains the function and states of the start button.

Combination Switch

Details the functions of the combination switch and its modes.

Overview of Indicator Lamps

Explains the meaning of various indicator lamps and their states.

Preparing for Use

Advice on Preparing for First Use

Provides essential advice and safety precautions before the first ride.

Running in the Engine

Gives guidelines for the engine's running-in phase.

Preparing the Vehicle for Difficult Operating Conditions

Advises on preparing the vehicle for challenging riding environments.

Preparing the Vehicle for Riding on Dry Sand

Details preparations for riding on dry sand.

Preparing the Vehicle for Riding on Wet Sand

Details preparations for riding on wet sand.

Preparing the Vehicle for Riding on Wet and Muddy Circuits

Details preparations for riding on wet and muddy circuits.

Preparing Vehicle for High Temperatures or Slow Riding

Advises on preparing the vehicle for high temperatures or slow riding.

Preparing the Vehicle for Low Temperatures or Snow

Details preparations for riding in low temperatures or snow.

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Lists essential checks and maintenance before riding.

Starting the Vehicle

Provides instructions and safety warnings for starting the vehicle.

Activating Launch Control

Explains how to activate and use the launch control system.

Activating Traction Control

Explains how to activate and use the traction control system.

Starting Off

Provides instructions on how to start moving from a standstill.

Shifting, Riding

Offers guidance on shifting gears and riding techniques.

Applying the Brakes

Explains how to apply the brakes effectively and safely.

Stopping, Parking

Provides instructions on how to stop and park the vehicle safely.

Refueling

Details the procedure and safety precautions for refueling.

Service Schedule

Required Work

Lists maintenance tasks required at different intervals.

Recommended Work

Lists recommended maintenance tasks for optimal performance.

Tuning the Chassis

Checking the Basic Chassis Setting with Rider's Weight

Explains how to adjust chassis settings based on rider weight.

Air Suspension XACT 5548

Describes the air suspension system used in the fork.

Compression Damping of the Shock Absorber

Explains the concept of compression damping in the shock absorber.

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Details how to adjust the low-speed compression damping.

Adjusting the High-Speed Compression Damping of the Shock Absorber

Details how to adjust the high-speed compression damping.

Adjusting the Rebound Damping of the Shock Absorber

Details how to adjust the rebound damping of the shock absorber.

Checking the Static Sag of the Shock Absorber

Explains how to check the static sag of the shock absorber.

Checking the Riding Sag of the Shock Absorber

Explains how to check the riding sag of the shock absorber.

Adjusting the Spring Preload of the Shock Absorber

Details how to adjust the spring preload of the shock absorber.

Adjusting the Riding Sag

Details how to adjust the riding sag.

Checking the Basic Setting of the Fork

Explains how to check the basic fork settings.

Adjusting the Fork Air Pressure

Details how to adjust the fork air pressure.

Adjusting the Compression Damping of the Fork

Details how to adjust the fork's compression damping.

Adjusting the Rebound Damping of the Fork

Details how to adjust the fork's rebound damping.

Service Work on the Chassis

Checking the Steering Head Bearing Play

Explains how to check for play in the steering head bearing.

Adjusting Steering Head Bearing Play

Provides steps to adjust steering head bearing play.

Removing the Fuel Tank

Details the procedure for removing the fuel tank.

Installing the Fuel Tank

Details the procedure for installing the fuel tank.

Checking the Chain Tension

Explains how to check the chain tension.

Adjusting the Chain Tension

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Checking/Correcting the Fluid Level of the Hydraulic Clutch

Changing the Hydraulic Clutch Fluid

Brake System

Checking the Free Travel of the Hand Brake Lever

Adjusting the Basic Position of the Hand Brake Lever

Checking the Brake Discs

Checking the Front Brake Fluid Level

Adding Front Brake Fluid

Checking the Front Brake Linings

Changing the Brake Linings of the Front Brake

Checking the Free Travel of Foot Brake Lever

Adjusting the Basic Position of the Foot Brake Lever

Checking the Rear Brake Fluid Level

Adding Rear Brake Fluid

Checking the Brake Linings of the Rear Brake

Changing the Rear Brake Linings

Wheels, Tires

Removing the Front Wheel

Installing the Front Wheel

Removing the Rear Wheel

Installing the Rear Wheel

Checking the Tire Condition

Checking Tire Pressure

Electrical System

Removing the 12-V Battery

Installing the 12 V Battery

Charging the 12 V Battery

Changing Main Fuse

Cooling System

Checking the Antifreeze and Coolant Level

Checking the Coolant Level

Tuning the Engine

Adjusting the Characteristic Map of the Throttle Response

Changing the Mapping

Adjusting the Idle Speed

Teaching the Throttle Valve Position

Service Work on the Engine

Changing the Fuel Screen

Checking the Engine Oil Level

Changing the Engine Oil and Oil Filter, Cleaning the Oil Screen

Details the procedure for changing engine oil, filter, and cleaning the screen.

Adding Engine Oil

Cleaning, Care

Cleaning the Motorcycle

Storage

Storage

Provides steps for preparing the motorcycle for long-term storage.

Putting into Operation After Storage

Details the steps for bringing the motorcycle back into service after storage.