Why are the vibration levels too high on my Husqvarna K 970 III Cutter?
Excessive vibration in your Husqvarna Cutter can stem from a few causes. Ensure the cutting blade is correctly installed and not damaged. Replace the cutting blade if it's defective and make sure the new one is not damaged. A defective vibration damping unit can also cause this issue; in that case, speak to your service agent.
What to do if the cutting blade doesn't rotate on my Husqvarna Cutter when I throttle up?
If the cutting blade on your Husqvarna Cutter isn't rotating when you throttle up, the belt might be too loose or defective; tighten or replace it. A defective clutch can also cause this, so speak to your service agent. Also, verify that the cutting blade is correctly installed.
Why is the temperature of my Husqvarna K 970 III Cutter too high?
If your Husqvarna Cutter is overheating, check if the air intake or cylinder flanges are blocked and clean them. Insufficient drive belt tension can also cause this, so examine the belt and adjust the tension. A defective clutch can also lead to high temperatures, so always cut at full throttle. Examine the clutch. If problems persist, speak to your service agent.
How to stop the cutting blade from rotating at idle speed on my Husqvarna K 970 III Cutter?
If the cutting blade rotates at idle speed on your Husqvarna Cutter, the idle speed is likely too high, so adjust it. A defective clutch can also cause this issue; in that case, speak to your service agent.
General| Engine type | 2-stroke |
|---|---|
| Power output | 5.8 kW |
| Displacement | 93.6 cm³ |
| Blade diameter | 350 mm |
| Max. cutting depth | 125 mm |
| Weight | 10.9 - 11.8 kg |
| Fuel tank volume | 0.95 l |
| Idle speed | 2800 rpm |
| Cutting diameter | 350 mm |
Details the components of the K 970 III model via numbered diagram and labels.
Illustrates and labels the components of the K 970 III Rescue model.
Shows and labels the parts of the K 970 SmartGuard model with a diagram.
Explains the meaning of various warning and information symbols found on the product.
Defines the meaning of warnings, cautions, and notes used in the manual.
Provides overarching safety guidelines for operating the power cutter.
Outlines critical safety precautions to follow during product operation.
Details safety requirements for the environment where the product is used.
Explains risks associated with product vibration and how to mitigate them.
Warns about the dangers of exhaust fumes and necessary precautions.
Highlights risks of dust exposure and necessary protective measures.
Lists essential protective gear required for safe operation.
Emphasizes checking and maintaining product safety features.
Describes the function and operation of the throttle trigger lockout.
Instructions for checking and ensuring the proper function of blade guards.
Explains the product's vibration damping system and its maintenance.
Details the function and safety considerations for the muffler.
Provides critical safety guidelines for handling and using fuel.
Outlines safety precautions to be taken before and during maintenance.
General warnings and instructions for handling and installing cutting blades.
Specifies the types of cutting blades suitable for the product.
Addresses issues related to cutting blade vibration and causes.
Information on using bonded abrasive cutting blades, including compatibility and safety.
Details on using diamond blades, including safety and usage recommendations.
Guidance on ensuring correct side clearance for diamond blade segments.
Strong warnings against using toothed blades due to kickback risks.
Steps to inspect the spindle shaft and flange washers during blade replacement.
Instructions for checking the arbor bushing for correct fit and function.
How to check that the cutting blade and spindle shaft rotation align.
Step-by-step guide for safely installing the cutting blade.
Instructions for reversing the cutting head for specific cutting situations.
Basic safety reminder before operating the product.
Explains what kickback is and its severe injury potential.
Describes the force that pulls the product during cutting and its impact.
Identifies the dangerous zone on the blade to avoid during operation.
Explains a specific type of kickback caused by blade binding.
Describes kickback where the blade climbs into the cut.
Details kickback caused by the cut closing and pinching the blade.
Special care and techniques for cutting pipes safely.
Method for cutting smaller diameter pipes.
Method for cutting larger diameter pipes in multiple steps.
Strategies and techniques to avoid dangerous kickback situations.
Essential techniques for safe and effective operation of the product.
Specific operating techniques for the K 970 SmartGuard model.
Methods to reduce dust generation during operation using a wet cutting kit.
Information about the product's two-stroke engine and fuel requirements.
Guidance on selecting and using the correct two-stroke oil.
Benefits and use of premixed alkylate fuel for the engine.
Instructions and ratios for mixing gasoline and two-stroke oil.
Steps for safely filling the fuel tank, including precautions.
Detailed procedure for starting the engine when it is cold.
Detailed procedure for starting the engine when it is warm.
Instructions for safely stopping the engine and the cutting blade.
General safety warning before performing maintenance.
A schedule outlining daily, weekly, monthly, and yearly maintenance tasks.
Instructions for cleaning the exterior of the product.
Guidance on cleaning the air intake to prevent overheating.
Procedure for inspecting the spark plug for engine performance issues.
Steps for performing a general inspection of the product's components.
Detailed instructions for replacing the drive belt.
Safety warning regarding the starter housing and recoil spring.
Steps to remove the starter housing from the product.
Instructions for replacing a broken or worn starter rope.
How to adjust the drive belt tension for optimal performance.
Procedure to adjust the tension of the recoil spring in the starter assembly.
Steps for cleaning the recoil spring assembly.
Instructions to reassemble the spring assembly after cleaning.
Steps to properly install the starter housing back onto the product.
Guidance on examining the carburetor for engine performance issues.
Steps to inspect the fuel tank, cap, and hoses for damage or leaks.
Procedure for adjusting the engine's idle speed to ensure proper operation.
Information about the fuel filter's function and replacement.
Steps for inspecting and replacing the air filter for optimal engine performance.
Instructions to check the water supply system for blockages or damage.
Lists common causes and solutions when the product fails to start.
Identifies issues and fixes for unintended blade rotation at idle.
Addresses problems where the blade fails to spin when the throttle is engaged.
Solutions for loss of power when the throttle is applied.
Discusses causes and solutions for excessive vibration during operation.
Identifies reasons for overheating and how to resolve them.
Solutions for engine performance degradation.
Addresses excessive dust generation and its causes.
Troubleshooting steps for a SmartGuard that is not moving smoothly.
Solutions for a SmartGuard that fails to retract automatically.
Guidelines for safely transporting, storing, and disposing of the product.
Provides detailed specifications for the K 970 III and K 970 SmartGuard models.
Specifies recommended dimensions for cutting blades compatible with the product.
Details on noise and vibration levels as per testing standards.
Information about the optional sensor for fleet management.
Description of the optional wheel kit for easier operation.
Information about the cutting trolley accessory for specialized cutting.
States compliance with relevant EU directives and harmonized standards.
Declares compliance with UK regulations and standards for the product.
To Next Page