Need help?Do you have a question about the Husqvarna PZ 72 and is the answer not in the manual?
General| Engine Manufacturer | Kawasaki |
|---|---|
| Fuel Type | Gasoline |
| Transmission Type | Hydrostatic |
| Engine Type | 4-Cycle |
| Cutting Width | 72 inches |
| Cutting Height, min | 1.5 inches |
| Cutting Height, max | 5 inches |
| Deck Type | Fabricated |
| Turning Radius | Zero-turn |
General information about directions and specifications for the machine.
Guidelines for public road transport and towing operations.
Intended use, safety, and general operating instructions.
Information on service, support, and identifying machine numbers.
Explanation of warning and information symbols used in the manual.
Visual guide to operational symbols, controls, and safety warnings.
Instructions to read manual and explanation of various safety symbols.
Specific warnings related to slope operation and machine rollover.
Information on noise levels according to EU directives.
Key safety guidelines and precautions for everyday operation.
Further safety advice for operation, traffic, and environmental hazards.
Recommended PPE and detailed safety for slope operation.
Safety precautions regarding children around the operating machine.
Precautions for gasoline handling, refueling, and hot engine warnings.
Safety guidelines for maintenance and repairs, including warnings.
Precautions for electrical sparking, battery hazards, and indoor operation.
Safety instructions for transport, loading, and hydraulic oil hazards.
Safety guidelines for Rollover Protection System and spark arrestor maintenance.
Diagram and identification of control elements on the machine.
How to operate steering controls for movement, turning, and zero turns.
Function of hour meter and adjustment of tracking knob for straight alignment.
Operation of parking brake, blade switch, and ignition switch.
Correct positions of the ignition switch for engine run and accessory use.
Operation of fuses, choke control, and cutting height adjustment pedals.
Adjusting seat position and operating the fuel shut off valve.
Safe refueling procedures, warnings, and advice on fuel blends.
Guidance for new users and basic steering for movement and turning.
Instructions for advanced steering maneuvers like zero turns.
Important information regarding control lever behavior in reverse.
Proper use of roll bar, seat belt, and pre-start checklists.
Step-by-step instructions for starting the engine.
Setting throttle, choke, and fuel valve before starting the engine.
Using the ignition key to start and run the engine, with important information.
Adjusting choke and throttle after starting for optimal engine operation.
Procedures for jump-starting the mower with a weak battery.
Releasing brake, moving controls, and adjusting cutting height.
Engaging deck, operating on hills, and associated safety warnings.
Step-by-step instructions for safely stopping the engine.
Best practices for mowing, including pattern and safety reminders.
Procedure for manual movement and conditions for maintenance.
Summary of maintenance checks by frequency (daily, yearly, hours).
Detailed maintenance tasks and intervals (50, 250, 500 hours).
Critical safety checklist before performing any service or adjustment.
Battery maintenance, removal, cleaning, and safety precautions.
Safety system verification, tire pressure, and caster wheel maintenance.
Visual check and detailed adjustment procedure for the parking brake.
Further parking brake adjustment and V-belt inspection.
Pump belt replacement procedures and general machine cleaning guidelines.
Schedule and general instructions for lubrication tasks.
Lubrication of wheels, deck components, and control cables.
Procedure for changing hydraulic fluid and filter.
Procedures for purging air from the hydrostatic drive system.
Troubleshooting for engine starting problems and rough running.
Troubleshooting for starter issues and weak engine performance.
Troubleshooting for vibration, overheating, slow movement, and mowing issues.
Procedures for preparing the machine for winter storage, including fuel warnings.
Information on ordering spare parts and annual service.
Diagrams of the electrical system and timer circuit.
Specifications for engine type, power, fuel, and transmission.
Data on frame, dimensions, weight, and vibration/noise levels.
Torque values for various fasteners, including U.S. and Metric standards.
Information on USA requirements and EU Declaration of Conformity.
Checklist for delivery service and points to inform the customer about.
Maintenance tasks to be performed after the first 10 operating hours.
Routine daily maintenance checks for the machine.
Maintenance tasks to be performed every 50 operating hours.
Maintenance tasks to be performed every 250 operating hours.
Maintenance tasks to be performed every 500 operating hours.
Maintenance tasks to be performed at least once per year.
To Next Page
