What to do if the malfunction indicator lamp lights up or flashes on my Husqvarna TE 250?
If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates a malfunction in the electronic fuel injection. Check the wiring for damage and the electrical plug-in connectors for corrosion and damage. Then, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
What to do if my Husqvarna Motorcycle engine dies during the trip?
If your Husqvarna Motorcycle engine dies during the trip, it could be due to a lack of fuel. Refuel if needed. The engine might be taking in false air, so check that the intake flange is firmly seated. The connector or ignition coil could also be loose or oxidized; clean the connector and treat it with contact spray. Finally, incorrectly stored ambient pressure could be the cause, so program the ambient air pressure.
Why is my Husqvarna TE 250 12-V battery discharged?
Your Husqvarna Motorcycle 12-V battery might be discharged because it is not being charged by the alternator or because of an unwanted electrical power consumer. Check the charging voltage and the stator winding of the alternator. Also, check the open-circuit current.
Why is there white smoke emission (steam in exhaust gas) from my Husqvarna TE 250?
White smoke emission (steam in exhaust gas) from your Husqvarna Motorcycle could be due to a damaged cylinder head or cylinder head gasket. Check these components for damage.
General| Displacement | 249 cc |
|---|---|
| Transmission | 6-speed |
| Cooling System | Liquid |
| Starter | Electric |
| Front Suspension | WP XPLOR 48 |
| Front Brake | Disc brake |
| Rear Brake | Disc brake |
| Bore x Stroke | 66.4 mm x 72 mm |
| Engine Type | 2-Stroke |
Explains the meaning of symbols used in the manual for clarity.
Details typographical formats used in the document for consistent understanding.
Defines the intended purpose and usage scope of the motorcycle.
Describes improper uses of the vehicle and potential dangers.
Provides general safety instructions and emphasizes reading the manual carefully.
Outlines warranty conditions and the importance of authorized service.
Notes on proper use of fuels and auxiliary substances, including environmental hazards.
Illustrates and labels key components visible from the front left side of the motorcycle.
Illustrates and labels key components visible from the rear right side of the motorcycle.
Details the location and importance of the VIN for identification.
Specifies the location of the type label for model identification.
Specifies where the engine number is located on the motorcycle for identification.
Describes the function and location of the clutch lever for operation.
Details the hand brake lever's location and its function for front brake engagement.
Describes the operation of the light switch for controlling headlights.
Explains the function of the map switch for altering engine characteristics.
Provides a general overview of the motorcycle's instrument cluster layout and functions.
Guides on how to adjust settings like units and clock on the instrument display.
Explains how to view and reset trip distance data on the instrument display.
Offers essential advice and safety warnings before the initial ride.
Provides guidelines for the engine's break-in period to ensure longevity.
Details adjustments needed for riding in challenging conditions like sand or mud.
Lists pre-ride checks and maintenance tasks for safe operation.
Details the procedure for safely starting the motorcycle's engine.
Explains correct braking techniques and safety warnings to prevent accidents.
Outlines essential maintenance tasks based on operating hours for motorsports use.
Lists recommended maintenance activities based on time or operating hours.
Explains how to adjust suspension settings based on rider weight for optimal handling.
Details how to adjust the high-speed compression damping for improved suspension response.
Guides on adjusting shock absorber spring preload for personalized suspension setup.
Guides on adjusting fork compression damping for ride quality.
Step-by-step instructions for safely lifting the motorcycle using a stand.
Provides guidance on cleaning fork dust boots to prevent seal damage.
Details the process for removing the lower triple clamp assembly.
Explains how to check for and correct play in the steering head bearings.
Explains how to adjust the hand brake lever for rider comfort and control.
Details how to check the front brake fluid level and potential issues.
Provides instructions on how to check the wear of front brake linings.
Explains how to check the free play in the foot brake lever for proper function.
Step-by-step instructions for safely removing the motorcycle's front wheel.
Detailed procedure for correctly installing the rear wheel after maintenance.
Guides on inspecting tires for wear, damage, and age for safe riding.
Explains how to check and adjust spoke tension for wheel integrity.
Step-by-step guide for safely removing the 12-V battery from the motorcycle.
Instructions on how to properly charge the motorcycle's 12-V battery.
Details on how to replace the main fuse for electrical system protection.
Procedure for removing the headlight assembly from the motorcycle.
Instructions on how to check the coolant level and antifreeze protection.
Details the steps for refilling the cooling system with the correct coolant.
Details the procedure for draining and refilling the motorcycle's cooling system.
Explains how to check throttle cable play for smooth operation and safety.
Guides on changing the throttle response by modifying the guide plate.
Explains how to set the engine's idle speed for smooth operation.
Provides instructions for replacing the fuel screen to ensure fuel system integrity.
Describes how to check the level of 2-stroke oil in the tank.
Provides instructions for cleaning the oil screen to ensure proper lubrication.
Details the procedure for draining and refilling the engine's gear oil.
Offers guidance on how to properly clean the motorcycle to maintain its appearance and function.
Outlines essential procedures for preparing the motorcycle for winter storage.
Details the steps and precautions for storing the motorcycle for extended periods.
Provides instructions for getting the motorcycle ready after a period of storage.
Presents detailed technical specifications for the motorcycle's engine.
Lists technical data related to the motorcycle's tires, including sizes and pressures.
Provides torque specifications for various chassis components for proper assembly.
Explains red symbols indicating critical errors requiring immediate attention.
Explains yellow/orange symbols indicating warnings or active driving aids.
Explains green/blue symbols reflecting informational content.
To Next Page
