Why are the values in my Husqvarna Motorcycle combination instrument deleted?
If the values in your Husqvarna Motorcycle combination instrument are deleted, such as time, stop watch, and lap times, the combination instrument battery is likely empty. Change the battery.
How to fix a Husqvarna Motorcycle when the engine won't crank?
If your Husqvarna Motorcycle engine cannot be cranked by the starter motor, here are a few things to investigate: * First, ensure you are using the correct start procedure. * Check the 12-V battery; it may be discharged and need charging. Also, check the charging voltage, open-circuit current, and the alternator's stator winding. * Inspect the main fuse; if it's blown, replace it. * The starter relay or the starter motor itself may be faulty and require inspection.
What causes a Husqvarna Motorcycle engine to overheat?
If your Husqvarna Motorcycle engine overheats, take the following steps: Check the coolant level and look for leaks in the cooling system. Ensure there's enough air stream, and switch off the engine when stationary. Clean the radiator fins if they are very dirty. If there's foam formation in the cooling system, drain and refill the coolant. Inspect the cylinder head and cylinder head gasket for damage. Replace any bent radiator hoses and check the thermostat, which should open at around 70 °C (158 °F).
What to do if my Husqvarna Motorcycle engine dies while riding?
If your Husqvarna Motorcycle engine dies during a trip, it could be due to a lack of fuel, so refuel. Another cause might be the engine taking in false air; check that the intake flange is firmly seated. Also, inspect the connector or ignition coil for looseness or oxidation, and clean the connector with contact spray if needed. Finally, if the ambient pressure is incorrectly stored, program the ambient air pressure.
Why does my Husqvarna Motorcycle have no idle speed?
If your Husqvarna Motorcycle engine has no idle speed, the spark plug may be defective, so change it. Faulty ignition could also be the cause; check the ignition coil, spark plug connector, and the stator winding of the alternator. Additionally, the idle speed might not be set correctly, so adjust it as needed.
What does it mean when the malfunction indicator lamp lights up on my Husqvarna Motorcycle?
If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, this could indicate a malfunction in the electronic fuel injection. Check the wiring for damage and electrical plug-in connectors for corrosion and damage. Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
General| Bore x Stroke | 66.4 mm x 72 mm |
|---|---|
| Starting System | Electric starter |
| Transmission | 6-speed |
| Engine Type | Single-cylinder, 2-stroke |
| Clutch | Wet multi-disc |
| Frame | Chromium Molybdenum steel |
| Front Suspension | WP XPLOR 48 |
| Rear Suspension | WP XPLOR shock absorber |
| Front Brake | 260 mm disc |
| Rear Brake | 220 mm disc |
| Front Wheel | 21" |
| Rear Wheel | 18" |
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use of the vehicle and compliance with regulations.
Describes what constitutes misuse of the vehicle and potential dangers.
Provides general safety instructions and emphasizes reading them carefully.
Warns against tampering with the noise control system and lists prohibited acts.
Provides crucial advice for safe vehicle operation, including dangers of accidents and poisoning.
Outlines essential rules and conditions to follow when performing work on the vehicle.
Stresses the importance of reading the manual for safe operation, handling, and service.
Details warranty conditions and the necessity of authorized workshop service.
Provides guidelines for using fuel and auxiliary substances safely and environmentally.
Recommends using approved spare parts and accessories for safety and performance.
Notes that figures may depict special equipment and components might be shown disassembled.
Provides information on contacting authorized dealers for assistance and support.
Illustrates the front left view of the vehicle with numbered components and their references.
Shows the location of the vehicle identification number on the steering head.
Indicates the location of the type label on the front of the steering head.
Specifies where to find the key number for the steering lock on the key ring.
Shows the location where the engine number is embossed on the engine.
Describes the clutch lever, its location, and automatic adjustment mechanism.
Details the location of the hand brake lever and its function for engaging the front brake.
Explains the function and states of the stop button on the left handlebar.
Describes the horn button's location and operation for EU/AR models.
Describes the function and states of the light switch for US models.
Details the location and operation of the turn signal switch for EU/AR models.
Describes the function and states of the start button for US models.
Explains the function and possible states of the map switch for different riding characteristics.
Details the indicator lamps for US models and their meanings.
Explains how to open the fuel tank filler cap, including safety warnings.
Describes the procedure for opening the 2-stroke oil tank cap.
Explains the function and states of the cold start button for fuel-injected engines.
Identifies the location of the shift lever and shows gear positions.
Explains the location and use of the side stand for parking the motorcycle.
Describes the function and location of the steering lock for EU/AR models.
Guides on how to unlock the steering using the steering lock.
Provides an overview of the combination instrument, its buttons, and display.
Explains how the combination instrument is activated.
Lists and explains possible messages displayed on the combination instrument.
Details the steps for adjusting settings like unit and time on the instrument.
Explains how to set or reset the service interval display.
Details how to view and reset speed, time, and distance 2 (DST2).
Provides essential safety advice and initial checks before the first ride.
Advises on preparing the vehicle for various challenging riding conditions like sand or mud.
Offers advice on preparing the vehicle for operation in hot conditions or slow riding.
Lists crucial checks and maintenance tasks to perform before every ride.
Details the safe procedure for starting the motorcycle's engine.
Provides instructions on shifting gears and general riding techniques.
Provides notes and warnings related to transporting the motorcycle.
Provides context on how service intervals may vary and where to find the latest schedule.
Lists essential maintenance tasks and their intervals based on operating hours.
Explains how to adjust the chassis settings based on the rider's weight for optimal handling.
Introduces the concept of high-speed and low-speed compression damping for shock absorbers.
Details how to adjust the low-speed compression damping on the shock absorber.
Describes the preparatory steps and main work for measuring rear wheel unloaded dimension.
Details the procedure for checking the riding sag of the shock absorber.
Provides information on checking the basic fork settings and potential issues.
Explains how to adjust the rebound damping on the fork legs.
Describes the available handlebar positions and mounting hole dimensions.
Explains how to safely raise the motorcycle using a lift stand.
Guides on how to safely remove the motorcycle from a lift stand.
Describes the process of bleeding the fork legs to remove air or excess pressure.
Details the steps required to remove the fork legs from the motorcycle.
Details how to install the fork protectors onto the front forks.
Describes the process of lubricating the steering head bearing.
Explains how to remove the front fender.
Details the procedure for correctly mounting the motorcycle seat.
Guides on how to remove the air filter box cover.
Details the procedure for removing the air filter from the air filter box.
Guides on how to correctly install the cleaned air filter.
Details the procedure for correctly installing the main silencer.
Guides on how to change the internal filling of the main silencer.
Details how to correctly install the right side cover.
Guides on how to safely install the fuel tank, including safety warnings.
Guides on inspecting the link fork for damage, cracking, or deformation.
Details the preparatory steps and procedure for checking throttle cable routing.
Details how to install the engine guard.
Guides on adjusting the hand brake lever position for standard TE models.
Explains how to check the free travel of the hand brake lever for special TE models.
Details how to adjust the free travel of the hand brake lever for special TE models.
Guides on how to add front brake fluid, including safety precautions.
Details the procedure for safely removing the front wheel.
Explains the importance of correct tire pressure and how to check it.
Details the procedure for safely removing the 12-V battery, including warnings.
Guides on how to correctly install the headlight mask and headlight assembly.
Explains how to change the turn signal bulb for EU/AR models.
Explains how to replace the battery for the combination instrument.
Provides a basic overview of the motorcycle's cooling system operation.
Details how to check the antifreeze and coolant levels with safety warnings.
Guides on how to drain the coolant from the system with safety warnings.
Explains how to check and measure the play in the throttle cable.
Describes how to program ambient air pressure for altitude adjustments.
Details how to adjust the shift lever's position for proper engagement.
Provides instructions and safety warnings for changing the fuel screen.
Guides on priming the 2-stroke oil pump, including warnings.
Offers detailed instructions and warnings for cleaning the motorcycle, emphasizing correct methods.
Explains the steps required to prepare the motorcycle for use after it has been stored.
Lists common faults, their possible causes, and recommended actions.
Explains the blink codes displayed by the malfunction indicator lamp.
Provides detailed technical specifications for the engine, including model variants.
Lists the specified tightening torques for various engine components.
Details the capacity for gear oil.
Details the capacity for coolant.
Details fuel tank capacity and reserve.
Lists technical specifications for the electrical system components like battery, lights, and fuses.
Specifies tire sizes and types for different models and regions.
Provides technical data for the front fork, including damping and spring settings.
Specifies the standard and recommended suppliers for brake fluid.
Provides guidelines and recommendations for coolant usage and antifreeze protection.
Details the standard and recommended engine oil specifications.
Lists specifications and recommendations for fork oil.
Provides specifications and recommendations for shock absorber fluid.
Specifies fuel requirements, including ethanol content limitations.
Lists recommended suppliers for air filter cleaner.
Lists recommended suppliers for chain cleaner.
Lists recommended suppliers for high viscosity grease.
Lists recommended suppliers for long-life grease.
Lists recommended suppliers for off-road chain spray.
Lists recommended suppliers for foam air filter oil.
Lists recommended suppliers for preserving materials.
Lists recommended suppliers for silicone spray.
Lists recommended suppliers for universal oil spray.
Explains the JASO T903 MA2 standard for motorcycle engine oils.
Explains SAE viscosity classifications for oils.
Describes the JASO FD classification for 2-stroke engine oil.
Defines electronic fuel injection with two injection valves.
Defines On-board diagnosis system for monitoring vehicle electronics.
Explains red symbols indicating error conditions requiring immediate intervention.
Explains yellow/orange symbols indicating errors or active driving aids.
Explains green/blue symbols that reflect information.
To Next Page
